Mikrotik GPEN11 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Mikrotik GPEN11 (5 sivua) kategoriassa Kytkin. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/5
GPEN11
This device allows powering a PoE capable device over the Ethernet,
using the same voltage, as provided with the DC input jack.
Powering
The device accepts power from direct-input power jack (5.5 mm
outside and 2 mm inside, female, pin positive plug) 12-57 V DC⎓.
Power output
The device supports PoE out from Ethernet port located under the
cover. You can power Mikrotik devices which supports passive powering
through Ethernet.
Mounting
Step 1:
1. Remove the cover screw using PH2 screwdriver;
2. Remove cover to access mounting points.
Step 2:
1. Drill holes using drill bid;
2. Insert dovels if needed;
3. Attach the unit to the wall, using wall and secure with screws.
Step 1. Step 2.
See mikrotik.com/products for the latest version of this document. Page 1, Document #46507 Modified on: 29.OCT.2019
Step 3:
1. Plug in the Ethernet cable going to the unit that will be powered;
2. Plug in power source for the GPEN.
* Outgoing Ethernet cable can be guided through position A, or B for cable leading into the wall.
Step 4:
1. Re-attach cover;
2. Secure cover using the screw;
3. Use the sticker to cover the screw location.
Step 3. Step 4.
When mounting on the wall, please ensure that cable feed is pointing downwards.
The IPX rating scale of this device is IPX0. We recommend using Cat6 shielded cables.
Accessories
Package includes the following accessories that come with the device:
•K-62 screw kit
Specifications
For more information about this product, specifications, pictures, downloads please visit our web page:
https://mikrotik.com/product/gpen11
See mikrotik.com/products for the latest version of this document. Page 2, Document #46507 Modified on: 29.OCT.2019
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the
unit to ensure compliance.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
See mikrotik.com/products for the latest version of this document. Page 3, Document #46507 Modified on: 29.OCT.2019
Tuotetiedot
| Merkki: | Mikrotik |
| Kategoria: | Kytkin |
| Malli: | GPEN11 |
Tarvitsetko apua?
Jos tarvitset apua merkille Mikrotik GPEN11 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kytkin Mikrotik Käyttöohjeet
15 Lokakuuta 2024
15 Lokakuuta 2024
Kytkin Käyttöohjeet
- Kytkin ORNO
- Kytkin D-Link
- Kytkin EBERLE
- Kytkin Lancom
- Kytkin IFM
- Kytkin TP Link
- Kytkin Totolink
- Kytkin StarTech.com
- Kytkin Yamaha
- Kytkin Cudy
- Kytkin Extron
- Kytkin Lindy
- Kytkin Netgear
- Kytkin Ecler
- Kytkin Digitus
- Kytkin Panasonic
- Kytkin LevelOne
- Kytkin Schneider
- Kytkin Engenius
- Kytkin EMOS
- Kytkin CSL
- Kytkin Smart-AVI
- Kytkin Generac
- Kytkin Dahua Technology
- Kytkin Cambium Networks
- Kytkin Sonance
- Kytkin Equip
- Kytkin Intermatic
- Kytkin Speaka
- Kytkin Nedis
- Kytkin Alcatel
- Kytkin Elation
- Kytkin Advantech
- Kytkin Atlona
- Kytkin Jung
- Kytkin Robbe
- Kytkin Luxul
- Kytkin Crestron
- Kytkin INOGENI
- Kytkin Elektrobock
- Kytkin PureLink
- Kytkin Kramer
- Kytkin ATen
- Kytkin Blustream
- Kytkin Vemer
- Kytkin WHALE
- Kytkin Tenda
- Kytkin Suevia
- Kytkin ZyXEL
- Kytkin Homematic IP
- Kytkin Vimar
- Kytkin Setti+
- Kytkin Intellinet
- Kytkin IOGEAR
- Kytkin Hager
- Kytkin Kathrein
- Kytkin Alfatron
- Kytkin DEHN
- Kytkin Berker
- Kytkin Kaiser
- Kytkin Adder
- Kytkin Finder
- Kytkin Brilliant
- Kytkin Roline
- Kytkin QNAP
- Kytkin DoorBird
- Kytkin Ebara
Viimeisimmät Kytkin Käyttöohjeet
16 Tammikuuta 2025
16 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
14 Tammikuuta 2025
14 Tammikuuta 2025