One Control OC10 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille One Control OC10 (9 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/9
KEY
All Red Lines Are Cables
Taking Signal Into OC10
All Green Lines Are Cables
Taking Signal Out Of OC10
OC 10 Crocodile Tail Loop Setup Utilising Tuner Out And One Loop
The above setup is using the OC10 in it’s most basic form were the guitar signal is run directly into
the rear main input jack.
The tuner output is selected when the OC10 is in program mode via the top row left hand footswitch
labelled “TUNER/L10”, when selected this mutes all output from unit except signal running from tuner
jack output.
Loop 1 is being utilised in this example. loops 1 thru 7 are internally connected so signal from main
input will always be running to OUT 1 and OUT 2 whether pedals are connected or not.
OUT 2 is being utilised in this example to run directly to amp input, OUT 1 and OUT 2 are in parallel
and are both supplied signal from the input jacks through loops 1 to 7, OUT 1 would be utilised if sig-
nal was required to run directly into IN 8 which is the start of the second run of loops (8,9,10)
SETUP 1
KEY
All Red Lines Are Cables
Taking Signal Into OC10
All Green Lines Are Cables
Taking Signal Out Of OC10
All Purple Lines Are Cables
Taking Signal Out of OC10
and Immediately Back Into
OC10
OC10 Setup Utilising Buffer Circuit, 1 Loop
from Loops 1 thru 7 and Loop 8
The above setup is using the OC10 with the guitar running into the Buffer circuit, Tuner out, loop 1
and loop 8
Utilising the Buffer circuit will give the signal increased strength and retention of clarity, primarily this
circuit is designed for running longer cable runs and running through multiple effects units which ulti-
mately can lower signal strength and dull the top end of the signal.
Loop 1 is being utilised in this example. loops 1 thru 7 are internally connected so signal from main
input will always be running to OUT 1 and OUT 2 whether pedals are connected or not.
SETUP 2
PAGE 1
In this example you can see that the echo unit in Loop 8 is connected via the S8 (Send 8) and R8
(Return 8) sockets, unlike Loops 1 thru 7 which are all internally connected, Loops 8 Thru 10 are not
and must be linked together using the Out and In sockets from each loop to run the signal into the next
loop.
The output of Loop 8 in this example is being used as the main out to run to the amplifier input, if you
needed to use more loops for effects in the second section of loops (8, 9, 10) then simply connect the
output from the previous loop into the input of the next loop. For example if you desired to run a reverb
unit in loop 9 you would need to link the out socket of Loop 8 to the input socket of loop 9, Loop 9 Out
would then become your main output.
SETUP 2 PAGE 2

Tuotetiedot

Merkki: One Control
Kategoria: Ei luokiteltu
Malli: OC10

Tarvitsetko apua?

Jos tarvitset apua merkille One Control OC10 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu One Control Käyttöohjeet

One Control

One Control OC10 Käyttöohje

16 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet