Onkyo IRK1553D Käyttöohje

Onkyo Ei luokiteltu IRK1553D

Lue alta 📖 käyttöohje suomeksi merkille Onkyo IRK1553D (3 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/3
- 1 -- 4 -
Rack Mount Kit Instruction Manual
PARTS ENCLOSED
1. Rack Mount Panels
Actual panels may vary by model.
2. Blank panel A
3.
Blank panel B (For 120 mm (4.7") height model)
4.
Blank panel (For 130 mm (5.1") height model)B
5. Spacer (For 130 mm (5.1") height model)
6. Screws A
For attaching the Rack Mount Panles to the
Unit (STEP 2).
7. Screws B
8. Washers A
9. Washers B
×
1 ×
1
× 1
× 4 × 6 × 6 × 6
×
1 ×
4
LR
 
Remove screws from the right side
of the cover. Do not remove feet from the
unit. Remove side screws only
from cover as indicated.
STEP
1
CAUTIONS
* Not suitable For In-Wall Mounting.
* Do not ground through the rack mount.
* Do not mount the unit to the rack alone, need one more person to hold the unit.
* Read "Important Safety Instruction" in the instruction manual and install the audio product with caution to avoid blocking its
ventilation.
Improper installation may cause a re or injury.
1. Ensure that there is adequate ventilation above and below the unit.
(according to the unit's instruction manual.)
2. For products that have vents on the side panels, please do not obstruct, in order to allow for ventilation.
3. Do not cover the ventilation holes on the unit installed.
4. For products that generate heat, such as an Amplier or Receiver, please use a minimum of one "U" (1.75") blank panel (or
space) above and below product for ventilation.
For best performance, it is recommended that DVD/CD players should be rack mounted below receivers to protect laser
mechanisms.
5. If rack is installed in a warm or enclose environment, use a cooling fan for ventilation.
* Please use caution when rack mounting products. To balance the weight and to keep the center of gravity as low as possible (in
order to keep from being too top heavy) mount heavier products towards the bottom of the rack.
SN29356000 F1803-0
STEP
STEP
4
5
Mount the blank panel B.
Mount the blank panel A.
 
or
More than one person is
needed for this step.
Please ensure that tack screw
and washers are assembled
as shown below to avoid
grounding through the rack
mount and blank panel B.
Please ensure that tack screw
and washers are assembled
as shown below to avoid
grounding through the blank
panel A.
Rack Mount
Panel
Blank
Panel B
Rack
 
Blank Panel A Rack
 
Please mount
panel with
sticker on back
side, oriented
as indicated on
sticker.
If the height of the unit being mounted is 155 mm (6.1") (âP2)
If the height of the unit being mounted is 120 mm (4.7") or 130 mm (5.1") ( âP3 - 4)
STEP
2
- 2 - - 3 -
Align the rack mount to front panel of
the unit.
Align the rack mount to front panel of
the unit.
Repeat the same procedure (step 1 - 2)
for the left side.
Repeat the same procedure (step 1 - 2)
for the left side.
Caution !
Make sure to use correct screw type and the rack mount panel is positioned correctly.
Make sure to use correct screw type and the rack mount panel is positioned correctly.
Align the top corner of the rack
mount panel to the top of the
front panel rst then align it
vertically to the front panel.
After installing the rack mount
panel on the right side, repeat
the same procedure (step 1 - 2)
for the left side.
Align the bottom corner of the
rack mount panel to the bottom
of the front panel rst then align
it vertically to the front panel.
After installing the rack mount
panel on the right side, repeat
the same procedure (step 1 - 2)
for the left side.
STEP STEP
2 2
When you install the rack mount panels, do not use any screws
other than those included in the package.
STEP
STEP
3
4
Mount the unit to the rack system.
Mount the blank
panel A.
Please see caution
section (âP4)
for ventilation
specics.
Please ensure that tack screw
and washers are assembled as
shown below to avoid grounding
through the blank panel A.
Please mount
panel with
sticker on
back side,
oriented as
indicated on
sticker.
For 155 mm (6.1") model For 120 mm (4.7") and 130 mm (5.1") model
More than one person is
needed for this step.
Please ensure that tack screw
and washers are assembled as
shown below to avoid grounding
through the rack mount.
Rack Mount Panel Rack
 
Blank Panel A Rack
 
STEP
3
Mount the unit to the rack system.
Please see caution
section (âP4)
for ventilation
specics.
More than one person is
needed for this step.
Please ensure that tack screw
and washers are assembled as
shown below to avoid grounding
through the rack mount.
If the height of the unit is
130 mm (5.1"), rst afx the
Spacers in the locations indi-
cated in the illustration at
left.
Caution ! When you install the rack mount panels, do not use any screws
other than those included in the package.
STEP
4 - 5

Tuotetiedot

Merkki: Onkyo
Kategoria: Ei luokiteltu
Malli: IRK1553D

Tarvitsetko apua?

Jos tarvitset apua merkille Onkyo IRK1553D esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Onkyo Käyttöohjeet

Onkyo

Onkyo IRK1553D Käyttöohje

24 Joulukuuta 2024
Onkyo

Onkyo IRK1804C Käyttöohje

24 Joulukuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet