Soundcraft Vi Dante Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Soundcraft Vi Dante (10 sivua) kategoriassa Sauvasekoitin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/10
ViDANTETM   Card User & Setup Guide
TheSoundcraft®Vi ViDANTE™ 64 64card is a  xinterfacebetweena 
series console and any Dante compatible device from Harman  or
other 3 rd   party manufacturer.  The card is available in two versions:
Local format) Rack/CSB (D21m3U andViStagebox(6Uformat).Note
thattheStageboxversionisan andIOcardonly does  not allow youto
connect a StageboxtotheconsoleusingDanteinsteadofMADI.
Dante provides network that a digital audio uses standard  Internet
Protocols over both100Mbps and 1Gigabit Ethernet.Danteuses
audio standardsindependent, high accuracy  networksynchronization 
toensureall allDantedevicesare synchronized at  times. Danteruns
on standard and computer networking hardware, does not  require
dedicatednetworkinfrastructure.
TheAudinate VirtualDante Soundcardsoftwareallowsconnectionof
a a network.PC/Macto Danteaudio Thissystemallowsthecomputer
to to the record and from playback Dante network using  most
common VirtualDAWpackages.Dante SoundcardusestheEthernet
port on the computer to communicate with the Dante network;  no
special hardware is required installing other than Dante Virtual
Soundcardsoftware.OneDVSlicensetoken is providedFOCwiththe
card,thislicensecanonlybeinstalledononespecificcomputer.
Additional information abouttheDANTEsystemincludingthelatest
softwareset toolsupand maybefoundontheAudinate®website
http://www.audinate.com/
ViDanteCardUser & SetupGuideV1.3
ConfiguringTheDanteCard
In a mannersimilartoCobraNet™,patchingontheconsolemakes a connectionbetweenconsoleI/O
slotchannels betweenandupto64channelsontheDante Connectionscard.  the areDantecards set
using a tool,inthiscasethe   Dante Controller software from Audinate®. As communication across the
Dante   network is essentially betweennamed cards andchannels the configuration must be correct
to toensurecardstalk listenand  the thecorrect/desiredchannelson Dantenetwork.
Thisuserguidesummarisestheprocessandprovides a simpleworkedexample; full setupdetailsand
configuration downloadabletoolsare fromtheAudinatewebsitewww.audinate.com.
Inadditionit is necessarytosetthe theclockstatusoftheDante card bothwithin networkandin
relation consoleto the  hardware.This  is described below.
ChannelCountSetup
TheDante default,carduses64 64 in and outchannelsby but becan restrictedtouselessinputor
outputchannelsif inrequired. consolesThismaybenecessaryonVi ordertoavoidexceedingthe
192in/192out channel limit of the local rack (or the 64in/64out channel limit if fitted in a Vi or
CompactStagebox).Forexample,if card,onlyoutput arechannels requiredontheDante theinput
channelscanbesetto0,tomaximisethenumberofinputchannelsavailablefor other cards.
TheDIPswitchS1ontheDantecardmainPCB is usedtosettheinputandoutputchannelcount,in
steps pageof on8chsfrom ‐0 64channels.Refer theto diagram thenext whichshowsthelocationof
the channel count DIP switch S1 and the factory default setup of 64 in/64 out. To create other
channel settingscount that   are not marked on the switch, add any two or 3 switch settings together,
ietoselect48chs,the32and16switchesshouldbemoveddowntotheselectedposition.Notethe
maximum countchannel (inputoroutput) is 64andminimum is zero.
SyncSetup
The Dante card can act as either a main clock source for the Dante network, or as a synchronised
clock.Ifthere  is only one console on the network, this will generally be set as the main clock
source  for the network,butincaseswith morethanoneconsole, or whereanotherdeviceacts as
the themain source clock, it willbenecessarytoset console'sDante card tobe asynchronised clock.
TheDante Danteclock sync statusissetupusing Controllersoftware(seelater in in thisguide),but 
addition Dantetothe clocksetup, hasthecard'sclock consolestatuswithinthe  tobeset.This is done
usingaDIPswitchS2on the Dante card main PCB. Refer to the diagram on the next page for the
locationandsettingofthisswitch.
MIX: Select     this position to make the Dante module lock to the console's  internal Wordclock, only
to the be used when the Dante card is set as Preferred Master for the Dante network.
Thissettingisthefactorydefault.
CARD: Selectthispositionto the to tomake consolelock theDantenetworkclock, beusedwhen
the Dante card is synchronised to the network. Note: In this case, a BNC wordclock cable must
also be connected from the Wordclock Out BNC connector on the Dante card, to the  console's
WordclockIN.
Notethat  it is alsonecessaryto thesetuptheclockingschemeof Dantenetworkcorrectly,toavoid
audioclicksanddropouts,pleaserefertothesectiontitledDeviceStatusand ClockStatus inthe
followingpages.
ViDanteCardUser & SetupGuideV1.3
ViDanteCardUser & SetupGuideV1.3
DIPswitchesS1 S2 &LocationDiagram
Refertothepreviouspageforinformationon ofthefunction theseswitches.
Note! pointSwitches  down to select channel count
ignorethe‘ON’legendonswitchbody!
Diagramshowsthedefaultsettingof64in / 64out

Tuotetiedot

Merkki: Soundcraft
Kategoria: Sauvasekoitin
Malli: Vi Dante

Tarvitsetko apua?

Jos tarvitset apua merkille Soundcraft Vi Dante esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Sauvasekoitin Soundcraft Käyttöohjeet

Sauvasekoitin Käyttöohjeet

Viimeisimmät Sauvasekoitin Käyttöohjeet

Alto

Alto PBM4 Sistema Käyttöohje

16 Tammikuuta 2025
Alto

Alto L-12 Käyttöohje

16 Tammikuuta 2025
Alto

Alto S-12 Käyttöohje

16 Tammikuuta 2025
Alto

Alto DJM-2 Käyttöohje

16 Tammikuuta 2025
Alto

Alto S-16 Käyttöohje

16 Tammikuuta 2025
Alto

Alto APM80.1000 Käyttöohje

16 Tammikuuta 2025
Alto

Alto AMX-120 Käyttöohje

16 Tammikuuta 2025
Alto

Alto S-8 Käyttöohje

16 Tammikuuta 2025
Alto

Alto LYNX-MIX82 Käyttöohje

16 Tammikuuta 2025
Alto

Alto DJM-3 Käyttöohje

16 Tammikuuta 2025