StarTech.com ST1000SPEXD4T Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille StarTech.com ST1000SPEXD4T (2 sivua) kategoriassa Verkkokortti/sovitin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 10, 2024
Product ID
ST1000SPEX2T / ST1000SPEX2LT / ST1000SPEXD4T
Port/LED/Connector Function
1Bracket
Used to secure onto the Host Computer
Low-Prole Bracket is included
Note: ST1000SPEX2LTships with the Low-Prole
bracket pre-installed
3 Ethernet Port Used to connect a to the Network Cable Network
Card
2Link/Activity LED
Indicators
Right LED: Link/Activity
Solid green: Active link
Flashing green: Activity
O: No active link
Left LED: Link Speed
Solid green: 1Gbps link
Solid orange: 10/100Mbps link
4PCIe p1-x1 Connector Insert into a PCI Express Slot
PCI Express Gigabit Ethernet Network Card
Requirements
For the latest requirements, please visit:
www.startech.com/ST1000SPEX2T
www.startech.com/ST1000SPEX2LT
www.startech.com/ST1000SPEXD4T
Computer with an available PCI Express Slot (x1, x2, x4, x8, or x16)
Package Contents
PCIe Network Card x 1
Low-Prole Bracket or Full-Height Bracket (ST1000SPEX2LT) x 1
Quick-Start Guide x 1
Installation
Install the PCI Express Card
WARNING!
Static electricity can cause severe damage to PCI Express cards. Ensure proper
grounding before opening the computer case or touching the PCI Express card. Use
an Anti-Static Strap when installing any computer component. If an Anti-Static Strap
isn’t available, discharge built-up static electricity by touching a large grounded metal
surface for several seconds. Handle the PCI Express card by its edges, avoiding contact
with the gold connectors.
1. Turn o the and any that are connected to it (for Computer Peripheral Devices
example, , , etc.).Printers External Hard Drives
2. Unplug the from the back of the .Power Cable Computer
3. Disconnect any that are connected to the .Peripheral Devices Computer
4. Remove the from the . Consult the documentation that came Cover Computer Case
with the for details about how to do this safely.Computer
5. Locate an open and remove the corresponding PCI Express Slot Slot Cover Plate
from the back of the . Consult the documentation that came with Computer Case
the for details about how to do this safely. This card works in PCI Express Computer
x1, x2, x4, x8, or x16 slots.
*Product may vary from image
*ST1000SPEX2T shown
1
3
2
4
Verify the Driver Installation
Windows
1. Navigate to the .Device Manager
2. Under Network Adapters Realtek PCIe GbE Family Controller, right-click and click
Properties.
3. Conrm that the is installed and working as expected.Driver
Linux
1. Run from the command line.lsmod | grep r8168
2. Verify that the is present in the command line. Driver
6. Gently insert the into the open and fasten the PCI Express Card PCI Express Slot
Bracket Computer Case to the back of the .
Note: If the PCI Express Card needs to be installed into a Small Form Factor or a
Low-Prole Desktop System, it may be necessary to replace the pre-installed standard
Full-Height Bracket with the included Low-Prole Bracket.
7. Return the back onto the .Cover Computer Case
8. Reconnect the to the back of the .Power Cable Computer
9. Reconnect all of the that were disconnected in .Peripheral Devices Step 3
10. Turn on the and .Computer Peripheral Devices
Install the Driver
1. Open an and navigate to:Internet Browser
www.startech.com/ST1000SPEX2T
www.startech.com/ST1000SPEX2LT
www.startech.com/ST1000SPEXD4T
2. Click the tab.Drivers & Downloads
3. Under , download the for the operating system.Driver(s) Driver
4. Extract the contents of the Driver Package
5. Execute the and follow the on-screen instructions to nish installing the Installer
Driver.
Linux
1. Extract the contents of the .Driver Package
2. Follow the installation instructions on the accompanying le.README.txt
Regulatory Compliance
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a dierent circuit than the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the device. If shielded interface cables are included with the product, or if additional components or accessories are
designated for use with the installation, they must be used to ensure compliance with FCC regulations.
ISED Statement / Déclaration d’ISED
CAN ICES-003(B) / NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
EU WEEE Directive
StarTech.com products must not be disposed of with household waste. StarTech.com
products must be disposed of at an authorized electrical and electronic equipment recycling
facility. By collecting and recycling waste, you help save natural resources and ensure that the
product is disposed of in an environmentally friendly and healthy way.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
FR
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands

Tuotetiedot

Merkki: StarTech.com
Kategoria: Verkkokortti/sovitin
Malli: ST1000SPEXD4T

Tarvitsetko apua?

Jos tarvitset apua merkille StarTech.com ST1000SPEXD4T esitä kysymys alla ja muut käyttäjät vastaavat sinulle