Sunbeam KE8850 Käyttöohje
Sunbeam
Vedenkeitin
KE8850
Lue alta 📖 käyttöohje suomeksi merkille Sunbeam KE8850 (2 sivua) kategoriassa Vedenkeitin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
Sunbeam’s safety precautions 2
Sunbeam’s 3-way safety system 3
Features of your kettle 4
Using your kettle 5
Care and cleaning 6
KE8850R | KE8850W | KE8850K | KE8850B | KE8850G | KE8850O | KE8850Y
Kettle User Guide
Care and Cleaning
Always disconnect the kettle from the power
outlet before cleaning.
Never immerse the kettle switch area, cord
or power base in water, or allow moisture to
come into contact with these parts.
Descale Your Kettle Regularly.
Mineral deposits in tap water solidify when
the water is heated; lime scale may be white,
coloured, even rusty-looking and is normally
visible but phosphate scale isn’t generally
visible although may cause the water to
appear cloudy when heated. This may cause
the interior of the water gauge to discolour,
cause overheating, trigger the boil-dry cut-out
mechanism or even reduce the kettle’s life.
Even in soft water areas it is important to
descale your kettle regularly to help maintains
its lifecycle.
NOTE: Failure to descale products regularly
can be deemed as negligent handling and any
faults caused by mineral build up will not be
covered by the Sunbeam 12 Month Guarantee.
To remove this build-up, use Sunbeam
Liquid Descaler, a simple to use, non-toxic
cleaner available from Sunbeam Appointed
Service Agents.
Alternatively:
1. Fill the kettle with 3 cups of white vinegar
and the remainder with water and allow to
stand overnight. DO NOT BOIL.
2. Empty the solution from the kettle. Any
stains remaining inside the spout can be
removed by rubbing with a damp cloth. Fill
the kettle with clean water, bring to boil
and then discard the water. Repeat and the
kettle will then be ready to use.
To clean the stainless exterior
The kettle surface may be wiped over with a
damp cloth and polished with a soft dry cloth.
CAUTION: Do not use chemicals, steelwool, or
abrasive cleaners to clean the outside of the
kettle, as these will scratch the stainless steel
surface.
To clean the mesh filter.
Open the lid. Grasp the top of the mesh
filter and pull upwards to remove. Wash in
warm soapy water and dry thoroughly before
replacing in the kettle.
Cleaning the concealed heating element
This kettle features a non-corrosive stainless
steel heating element. Over time, scale may
build up on the concealed element inside
the kettle, causing discolouration that may
have the appearance of rust. Be assured this
is not rust. If this occurs clean with a green
Scotchbrite® scourer or similar and a suitable
abrasive cleaning cream. Rinse and clean
thoroughly with tap water before using your
kettle again.
12 Month Replacement Guarantee
Upon receipt of your claim, Sunbeam will seek to
resolve your difficulties or, if the product is defective,
advise you on how to obtain a replacement or refund.
To assist us in managing warranty claims, we
recommend you register your product as soon as
practicable after purchase by creating a MySunbeam
account on our website and uploading a copy of your
original receipt.
In order to make a claim under our warranty, you must
have the original proof of purchase documentation
for the product and present it when requested (if not
already uploaded to our website).
Should your product develop any defect within 12
months of purchase because of faulty materials
or workmanship, we will replace or repair it, at our
discretion, free of charge. A product presented for
repair may be replaced by a refurbished product of
the same type rather than being repaired. Refurbished
parts may be used to repair the product.
Our replacement or repair warranty only applies
where a defect arises as a result of faulty material
or workmanship during the warranty period. Your
warranty does not cover misuse or negligent handling
(including damage caused by failing to use the
product in accordance with this instruction booklet),
accidental damage, or normal wear and tear.
Your warranty does not:
• cover freight or any other costs incurred in making
a claim, consumable items, accessories that by their
nature and limited lifespan require periodic renewal
(such as filters and seals) or any consequential loss
or damage; or
• cover damage caused by:
- power surges, power dips, voltage supply
problems, or use of the product on
incorrect voltage;
- servicing or modification of the product other
than by Sunbeam or an authorised Sunbeam
service centre;
- use of the product with other accessories,
attachments, product supplies, parts or devices
that do not conform to Sunbeam specifications; or
- exposure of the product to abnormally corrosive
conditions; or
• extend beyond 3 months if the product is
used in commercial, industrial, educational or
rental applications.
The benefits given to you by our warranty are in
addition to other rights and remedies under law
in relation to the product.
In Australia our goods come with guarantees that
cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Our goods also come with guarantees that cannot
be excluded under the New Zealand Consumer
Guarantees Act.
If your warranty claim is not accepted, we will inform
you and if requested to do so by you, repair the
product provided you pay the usual charges for such
repair. You will also be responsible for all freight and
other costs.
Should your product require repair or service after
the warranty period, contact your nearest Sunbeam
service centre.For a complete list of Sunbeam’s
service centres, visit our website or call our customer
service line for advice on 1300 881 861 in Australia,
or 0800 786 232 in New Zealand.
Should you experience any difficulties with
your product during the warranty period,
please contact our customer service line
for advice on 1300 881 861 in Australia, or
0800 786 232 in New Zealand.
Australia | www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand | www.sunbeam.co.nz
0800 786 232
Level 6, Building 5, Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
6 7
Need help with your appliance?
Contact our customer service team or visit our website
for information and tips on getting the most from your appliance.
New Zealand
Phone 0800 786 232
Mail Level 6, Building 5, Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Visit www.sunbeam.co.nz
Australia
Phone 1300 881 861
Mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia
Visit www.sunbeam.com.au
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trademark. Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise, the product you buy may differ slightly from the one
shown here. Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2015.
3011A
3011-A-IB.indd 1 26/08/2015 3:26:47 PM
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS
FOR YOUR SUNBEAM KETTLE.
• Always operate the kettle on a flat,
level surface.
• Boiling water will scald. Do not leave a
boiling or hot kettle near or where children
may touch it.
• Do not leave the power cord near the edge of
a bench top where children may touch or pull it.
• Boiling water may be ejected, if overfilled.
• Do not open lid while water is boiling.
• Avoid spillage on the connector.
• Do not operate the kettle without water.
• Always turn the power off and unplug the
cord while the kettle is NOT in use.
• Your Kettle must only be used with the
power base supplied.
• Do not move kettle while switched on.
Sunbeam is very safety conscious when
designing and manufacturing consumer
products, but it is essential that the
product user also exercise care when using
an electrical appliance. Listed below are
precautions which are essential for the safe
use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power
outlet before you insert or remove a plug.
Remove by grasping the plug - do not pull on
the cord.
• Turn the power off and remove the plug
when the appliance is not in use and before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked on
the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may
be high when the appliance is operating.
• Never leave an appliance unattended while
in use.
• The heating element surface is subject to
residual heat after use.
• Do not use an appliance for any purpose
other than its intended use as this may
result in potential injury.
• Do not place an appliance on or near a hot
gas flame, electric element or on a heated
oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance
hang over the edge of a table or bench top
or touch any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water or
any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses;
by clients in hotels, motels and other
residential type environments; bed and
breakfast type environments.
If you have any concerns regarding the
performance and use of your appliance, please
visit www.sunbeam.com.au or contact the
Sunbeam Consumer Service Line. Ensure the
above safety precautions are understood.
Sunbeam’s 3-Way Safety System
Safety is a major consideration in the design
of a Sunbeam kettle. This is why we have
developed our 3-Way Safety System, which
ensures that your kettle will:
1. Automatically switch off after boiling
For convenience, safety and energy
efficiency, your Sunbeam kettle will
automatically switch off after boiling.
2. Cut-out for boil-dry protection.
If the kettle is operated without water, it
will automatically cut-out, preventing any
damage to the element.
If this occurs, allow the kettle to cool before
filling with cold water and re-boiling.
3. Shut-down in case of overheating
In the event of overheating, the kettle will
automatically shut down to prevent further
damage. Should this occur, take your kettle
to a Sunbeam Service Centre or Appointed
Service Agent.
Features of your Marc Newson Kettle
1. 1.5L stainless steel design
6 cup capacity kettle constructed using
long life stainless steel.
2. 2300 watt concealed element
The fast boil 2300 watt element is
concealed in the base of the kettle for
longer element life.
3. LED boiling indicators
Located at switch of the kettle and
illuminates during boiling.
4. 360 degree cordless power base
Designed to allow you to place the kettle
on the base in any direction.
1
5
2
6
3
4
7
5. Removable mesh filter
Keeps the water clean of any
foreign matter and is removable
or easy cleaning.
6. Cord Storage
The cord can be wrapped around
the storage facility underneath the
power base
7. On/Off switch with auto cut-off
Switches the kettle off
automatically after boiling.
Using your Marc Newson Kettle
Before using your kettle.
It is recommended that you clean your kettle
before use by filling the kettle with water, up to
the maximum level indicator, boil and discard.
Using your kettle.
1. To fill the kettle, remove it from the power
base and lift the lid. Alternatively, the kettle
may be filled through the pouring spout.
2. Fill the kettle with the desired amount
of water. Too little water will result in the
kettle switching off before the water has
boiled.
NOTE: Do not fill the kettle over the
maximum level, as water may spill out of
the spout when boiling.
3. Push the lid closed firmly until it locks into
position.
4. Place the kettle on the power base and
connect the plug into a 230/240 Volt AC
power outlet. Turn the power ON.
5. Press the ON/OFF button downwards at the
base of the kettle. The boiling indicators will
illuminate to indicate the kettle is heating.
The kettle will switch off automatically once
the water has boiled.
NOTE: Ensure that the ON/OFF switch is
clear of obstructions and the lid is firmly
closed. The kettle will not turn off if the
ON/OFF switch is constrained or if the lid
is left open. Do not remove the kettle from
the power base while water is heating.
6. Lift the kettle from the power base and
pour the water.
NOTE: Use caution when pouring the water
from your kettle, as boiling water will scald.
7. The kettle may be stored on the power
base while not in use. The kettle will not
re-boil until the ON/OFF switch is pressed
downward.
NOTE: Ensure the power is turned off at the
power outlet when the kettle is not in use.
Should you accidentally allow the kettle to
operate without water, boil-dry protection
will automatically switch it off. If this occurs,
allow the kettle to cool before filling with
cold water and re-boiling.
Cord Storage Facility.
Excess cord can be stored by winding the
cord around the storage facility underneath
the power base.
2 3 4 5
Important Instructions - retain for future use
3011-A-IB.indd 2 26/08/2015 3:26:47 PM
Tuotetiedot
| Merkki: | Sunbeam |
| Kategoria: | Vedenkeitin |
| Malli: | KE8850 |
Tarvitsetko apua?
Jos tarvitset apua merkille Sunbeam KE8850 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Vedenkeitin Sunbeam Käyttöohjeet
17 Lokakuuta 2024
Vedenkeitin Käyttöohjeet
- Vedenkeitin Adler
- Vedenkeitin DeWalt
- Vedenkeitin Imarflex
- Vedenkeitin Kogan
- Vedenkeitin Midea
- Vedenkeitin Gourmetmaxx
- Vedenkeitin Gorenje
- Vedenkeitin Sencor
- Vedenkeitin Khind
- Vedenkeitin Concept
- Vedenkeitin Tower
- Vedenkeitin Salton
- Vedenkeitin Eldom
- Vedenkeitin Muse
- Vedenkeitin Hamilton Beach
- Vedenkeitin Mystery
- Vedenkeitin Mellerware
- Vedenkeitin Zwilling
- Vedenkeitin Izzy
- Vedenkeitin Zeegma
- Vedenkeitin Yamazen
- Vedenkeitin BOSFOR
Viimeisimmät Vedenkeitin Käyttöohjeet
27 Lokakuuta 2024
27 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024