Sunbeam SB8300 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Sunbeam SB8300 (2 sivua) kategoriassa Rauta. Tämä opas oli hyödyllinen 14 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
1
Opening
Support the ironing board in the vertical
position and lift the release lever. Allow the
top leg to drop to the floor while lowering the
board until horizontal.
Adjusting the height
To increase the height of the board, lift the
release lever slightly and pull the board
upward to the desired height setting. To lower
the height, lift the release lever slightly and
gently push downwards on the board until the
desired height setting is reached.
Closing
Ensure that the iron rest is stowed under the
board before closing. To close, raise the rear
of the board (nearest the iron rest) while
lifting the release lever, allowing the rear legs
to rise and the to board swing into the
vertical position.
Using the retractable iron rest
To use the iron rest, slide it out from
underneath the board so that the rest is fully
extended. When you have finished ironing,
push the iron rest firmly back into position
underneath the board before storing.
Fitting the cover
Pull tightly on the drawstring to tighten the
cover. Press the toggle and slide it towards
the board to tighten. Release to lock in
position.
Caring for the cover
The cotton cover has been treated with
Teflon® Fabric Protector from DuPont. Water
rolls off and stains just wipe away. Teflon®
provides maximum water and stain
repellency, but still allows the fabric to
breathe. A heat treatment (warm ironing or
tumble drying) will optimize the performance
of Teflon®. Warm machine wash on a gentle
cycle. Line or tumble dry. Do not dry clean.
To keep the cover’s shape, fit to the board
while still damp and iron dry.
Operating Instructions for your
ironing board
2
5 Year Replacement Guarantee
We are so confident of the quality of our
metal ironing board frame should it develop
any malfunction within five years of purchase
(12 months commercial use), due to faulty
materials or manufacture, we will replace it
for you free of charge.
Should you experience any difficulties with
your metal ironing board frame, please
contact our customer service line for advice
on 1300 881 861 in Australia, or 0800
786 232 in New Zealand. Alternatively, you
can send a written claim to Sunbeam at the
address listed below. Upon receipt of your
claim, Sunbeam will seek to resolve your
difficulties or, if the metal ironing board
frame is defective, advise you on how to
obtain a replacement of refund.
Your Sunbeam 5 Year Replacement
Guarantee obviously does not cover misuse
or negligent handling and normal wear and
tear. Similarly, your 5 Year Replacement
Guarantee does not cover freight or any other
costs incurred in making a claim. Please
retain your receipt as proof of purchase.
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
product.
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law and under the New Zealand
Consumer Guarantees Act. In Australia you
are entitled to a replacement or refund for a
major failure and for compensation for any
other reasonably foreseeable loss or damage.
You are also entitled to have the goods
repaired or replaced if the goods fail to be
of acceptable quality and the failure does
amount to a major failure.
Should your metal ironing board frame
require repair or service after the guarantee
period, contact your nearest Sunbeam
service centre.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Tuotetiedot
| Merkki: | Sunbeam |
| Kategoria: | Rauta |
| Malli: | SB8300 |
Tarvitsetko apua?
Jos tarvitset apua merkille Sunbeam SB8300 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Rauta Sunbeam Käyttöohjeet
30 Joulukuuta 2025
14 Joulukuuta 2024
17 Lokakuuta 2024
Rauta Käyttöohjeet
- Rauta Adler
- Rauta Bosch
- Rauta Electrolux
- Rauta Arcelik
- Rauta Philips
- Rauta Russell Hobbs
- Rauta AEG
- Rauta Cecotec
- Rauta Imarflex
- Rauta Create
- Rauta G3 Ferrari
- Rauta Morphy Richards
- Rauta Conair
- Rauta Orbegozo
- Rauta Panasonic
- Rauta Sencor
- Rauta MPM
- Rauta Khind
- Rauta Taurus
- Rauta Concept
- Rauta Hyundai
- Rauta Ufesa
- Rauta Scarlett
- Rauta Rowenta
- Rauta Tower
- Rauta Braun
- Rauta Eldom
- Rauta Elba
- Rauta Brentwood
- Rauta Black And Decker
- Rauta Hamilton Beach
- Rauta Di4
- Rauta Mellerware
- Rauta Tefal
- Rauta Silvercrest
- Rauta Trisa
- Rauta Izzy
- Rauta Polti
- Rauta Girmi
- Rauta Camry
- Rauta Yamazen
- Rauta Calor
- Rauta Black Decker
- Rauta DPM
- Rauta Oster
- Rauta Easy Home
- Rauta Lenoxx
- Rauta Comelec
- Rauta Igenix
- Rauta T-fal
Viimeisimmät Rauta Käyttöohjeet
31 Maaliskuuta 2025
31 Maaliskuuta 2025
12 Maaliskuuta 2025
5 Maaliskuuta 2025
5 Maaliskuuta 2025
5 Maaliskuuta 2025
5 Maaliskuuta 2025
27 Helmikuuta 2025
27 Helmikuuta 2025
27 Helmikuuta 2025