WAC Lighting Tube Architectural DS-WD05-S27S-BK Käyttöohje
WAC Lighting
Helpotus
Tube Architectural DS-WD05-S27S-BK
Lue alta 📖 käyttöohje suomeksi merkille WAC Lighting Tube Architectural DS-WD05-S27S-BK (3 sivua) kategoriassa Helpotus. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/3
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2016
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Tube Architectural - LED Wall Mount
DS-WS05, WS06, WS08, DS-WD05, WD06, WD08
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
FIG.1
Wire Connector Junction Box Screw Gasket
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2016
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Tube Architectural - LED Wall Mount
DS-WS05, WS06, WS08, DS-WD05, WD06, WD08
OVERVIEW
It is surface mount down light, included ceiling mount, pendant mount, single direction wall wash and up-down direction wall wash.
Check catalog for various mount type, size, beam angle and color choices.
FIXTURE INSTALLATION
1. Carefully unpack your new xture and lay out all the parts on a clear area. Be carefully not to lose any small parts necessary for installation.
(See ) FIG.1
2. Remove the screw holding mounting plate to xture, and remove mounting plate from xture. (See ) FIG.2
3. Secure mounting plate to the junction box in wall provided by others. (See ) FIG.2
4. Pull power supply wires out of junction box through mounting plate. Connect black xture wire to hot wire, white xture wire to neutral
wire and green xture wire to ground. This xture oers 0-10V dimming capability. To utilize, connect purple xture wire to hot dimming
wire and gray xture wire to neutral dimming wire. If not utilizing dimming, terminate the dimming wires by capping them separately. After
wires are connected securely, tuck them carefully inside the junction box . (See ) FIG.2
5. Put the xture to the mounting plate, and secure with screws and gasket.(See ) FIG.2
Mount Plate
Ground Wire
ScrewGasket
Junction Box
FIG.2
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2016
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
REFLECTOR REPLACEMENT
1. Remove panel assembly by loosening the xture screw and gasket, remove three chips to change reector. ( )FIG.3
2. Replace your beam angle reector on panel and x the clips. ( )FIG.4
LED REPLACEMENT
1. Loosen the screw and gasket (See ), remove the panel assembly (See ).FIG.5 FIG.6
2. Loosen the LED holder and LED screws, carefully disconnect LED connector from driver connector and replace LED by removing LED
mounting screws. (See ).FIG.7
DRIVER REPLACEMENT
1. Loosen the screw and gasket (See ), remove the cover assembly (See ).FIG.8 FIG.9
2. Loosen the LED driver screws, carefully disconnect LED driver connector from LED connector and replace driver by removing driver
mounting screws. (See ). FIG.10
COMPLETING THE INSTALLATION
To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of xture plate where it meets the wall leaving a space at bottom to allow moisture a means to escape.
Remove three clips
Replace dierent
beam angle reector
Loosen the xture
screws and gaskets
Loosen the xture
screws and gaskets
Remove panel
assembly
Remove panel
assembly
LED holder
LED holder
Screws
Connector
LED
Put on reector
and x clips
FIG.3
FIG.5
FIG.8
FIG.6
FIG.9
FIG.7
FIG.10
FIG.4
INSTALLATION INSTRUCTION
Tube Architectural - LED Wall Mount
DS-WS05, WS06, WS08, DS-WD05, WD06, WD08
Tuotetiedot
| Merkki: | WAC Lighting |
| Kategoria: | Helpotus |
| Malli: | Tube Architectural DS-WD05-S27S-BK |
Tarvitsetko apua?
Jos tarvitset apua merkille WAC Lighting Tube Architectural DS-WD05-S27S-BK esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Helpotus WAC Lighting Käyttöohjeet
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
Helpotus Käyttöohjeet
- Helpotus Stamos
- Helpotus ORNO
- Helpotus Ledlenser
- Helpotus Bosch
- Helpotus AFX
- Helpotus DeWalt
- Helpotus Hama
- Helpotus Neewer
- Helpotus Hazet
- Helpotus Philips
- Helpotus Schwaiger
- Helpotus Godox
- Helpotus IKEA
- Helpotus TP Link
- Helpotus Razer
- Helpotus Kogan
- Helpotus Behringer
- Helpotus GoGEN
- Helpotus Nitecore
- Helpotus Kichler
- Helpotus Trust
- Helpotus Integral LED
- Helpotus Lutec
- Helpotus Golden Lighting
- Helpotus ET2
- Helpotus Quoizel
- Helpotus Crystorama
- Helpotus Brennenstuhl
- Helpotus Varaluz
- Helpotus FIAP
- Helpotus Aputure
- Helpotus Media-tech
- Helpotus NEO Tools
- Helpotus Gemini
- Helpotus Westinghouse
- Helpotus Canarm
- Helpotus Klein Tools
- Helpotus Schneider
- Helpotus Dainolite
- Helpotus Tesy
- Helpotus Martin
- Helpotus EMOS
- Helpotus Sharper Image
- Helpotus Manfrotto
- Helpotus Fluval
- Helpotus Ryobi
- Helpotus Nanlite
- Helpotus BeamZ
- Helpotus Steinel
- Helpotus Maxim
- Helpotus Nordlux
- Helpotus Brandson
- Helpotus Aplic
- Helpotus CSL
- Helpotus Bearware
- Helpotus Moen
- Helpotus NUVO
- Helpotus Maginon
- Helpotus Sonneman
- Helpotus Milwaukee
- Helpotus Generac
- Helpotus OttLite
- Helpotus Kern
- Helpotus Ansmann
- Helpotus Showtec
- Helpotus Busch + Müller
- Helpotus Valerie Objects
- Helpotus V-Tac
- Helpotus Wireless Solution
- Helpotus Infinity
- Helpotus Nedis
- Helpotus Elation
- Helpotus Chauvet
- Helpotus Karma
- Helpotus TFA
- Helpotus Weeylite
- Helpotus Lumie
- Helpotus ESYLUX
- Helpotus Livarno Lux
- Helpotus Omnitronic
- Helpotus Eurolite
- Helpotus Casalux
- Helpotus Innoliving
- Helpotus Aqara
- Helpotus Beghelli
- Helpotus Middle Atlantic
- Helpotus Rosco
- Helpotus DeSisti
- Helpotus American DJ
- Helpotus Astera
- Helpotus EXO
- Helpotus Novy
- Helpotus Profoto
- Helpotus Claypaky
- Helpotus GRE
- Helpotus Ikan
- Helpotus Ring
- Helpotus Perel
- Helpotus Blackburn
- Helpotus Sigma
- Helpotus Rayzr 7
- Helpotus Excello
- Helpotus Vimar
- Helpotus Genaray
- Helpotus Altman
- Helpotus Setti+
- Helpotus Kanlux
- Helpotus ARRI
- Helpotus Yamazen
- Helpotus Osram
- Helpotus Elan
- Helpotus Light4Me
- Helpotus GlobalTronics
- Helpotus Lume Cube
- Helpotus Digipower
- Helpotus Fiilex
- Helpotus Bresser
- Helpotus Currey & Company
- Helpotus Kino Flo
- Helpotus Cateye
- Helpotus GVM
- Helpotus Maxxmee
- Helpotus Wiesenfield
- Helpotus Sun Joe
- Helpotus Lexon
- Helpotus Rollei
- Helpotus Angler
- Helpotus Raya
- Helpotus Dracast
- Helpotus ColorKey
- Helpotus Luxli
- Helpotus LUPO
- Helpotus Livex Lighting
- Helpotus Eglo
- Helpotus Hinkley Lighting
- Helpotus Underwater Kinetics
- Helpotus Ranex
- Helpotus COLBOR
- Helpotus Fuzzix
- Helpotus DMT
- Helpotus Sea&Sea
- Helpotus Lucide
- Helpotus Peerless-AV
- Helpotus LumenRadio
- Helpotus Paulmann
- Helpotus HQ Power
- Helpotus Heitronic
- Helpotus Govee
- Helpotus Melinera
- Helpotus Sagitter
- Helpotus Yongnuo
- Helpotus Qazqa
- Helpotus Audibax
- Helpotus Mazda
- Helpotus Triton Blue
- Helpotus Singercon
- Helpotus Hudson Valley
- Helpotus Forte Lighting
- Helpotus ETC
- Helpotus Portman
- Helpotus Litepanels
- Helpotus Perfect Christmans
- Helpotus XQ-Lite
- Helpotus Obsidian
- Helpotus Blizzard
- Helpotus Amaran
- Helpotus Enttec
- Helpotus Fotodiox
- Helpotus Halo
- Helpotus Light & Motion
- Helpotus Intellytech
- Helpotus Trio Lighting
- Helpotus DCW
- Helpotus Kinotehnik
- Helpotus GLP
- Helpotus SLV
- Helpotus Rotolight
- Helpotus Quasar Science
- Helpotus Kuzco
- Helpotus Lowel
- Helpotus Schonbek
Viimeisimmät Helpotus Käyttöohjeet
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
2 Huhtikuuta 2025