AFX Satellite STLF4450L30SN Käyttöohje

AFX Helpotus Satellite STLF4450L30SN

Lue alta 📖 käyttöohje suomeksi merkille AFX Satellite STLF4450L30SN (2 sivua) kategoriassa Helpotus. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/2

LED Indoor Luminaires Model # STLF4450L30SN

Fixed Rail Ceiling Mount

120VAC / 60Hz

Page 1 of 2 8061273 R0

Luminous Intensity Distribution

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property damage.

 It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120VAC, 60Hz fused circuit. This xture is compatible with 2-wire Triac dimmers. / ELV

 Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp locations.

 Disclaimer

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES- -005 (B). These limits are designed to 005 (B) / NMB

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminai re.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing

any part of this xture.

B. Remove xture from carton; remove components from

hardware kit.

C. Remove round gem bar (2 from the xture by removing two )

screws (3).

D. Install round gem bar (2) to junction box (not provided) by

securing it with two #8- screws (4). 32

2. Wiring.

All wiring must take place inside junction box (not included).

Caution: Make sure power is o at fuse or circuit breaker box.

Check power wires for damage or scrapes. If the power supply

wires are within three inches of the driver, use a wire suitable for at least 90C (194F).

Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a

qualied electrician before installing.

A. This unit will not operate properly unless connected to a “grounded” electrical

circuit. Electrical shock, overheating, low or no light output, and shortened

LED life can result if proper grounding is not done. Securely attach power

source ground wire and xture ground wire to green ground screw on

rectangular mounting bracket.

B. Make all wire connections to appropriate wire. Secure with wire nuts

(provided).

C. For none-dimming xture. Fixture will operate normally w/o connection to

any dimmers. Connect white xture lead to white (N) wire from supply power

source. Connect black xture lead to black (L) wire from supply power source.

D. For TRIAC dimming. Connect white xture lead to white (N) wire from

dimming source dimmer wiring instructions. Connect black xture lead to per

black (L) wire from dimming source per dimmer wiring instructions.

E. Do not mix wires. Pull on each wire lead to make sure connections are

secure. Make certain no bare wires are exposed outside of wire connectors.

Tuck all connections neatly into junction box.

3. Mounting.

A. Install xture (1) to round gem bar (2) with two screws (3).

4. Power to the xture can now be restored.

LED Indoor Luminaires Model # STLF4450L30SN

Fixed Rail Ceiling Mount

120VAC / 60Hz

Page 1 of 2 8061273 R0

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due

to improper installation, misuse, mishandling or damage incurred in transit.

REPLACING THE LED DRIVER

IMPORTANT! Do NOT disassemble product. This operation is only for the replacement of a faulty LED Driver.

IMPORTANT! It is recommended that the replacement of an LED driver be completed by a qualied electrician.

CAUTION! Turn o main power at fuse or circuit breaker box.

Disassembly:

1. Remove xture from wall by removing (2) canopy

screws.

2. Disconnect LED driver power wires from power supply

wires in junction box by removing wire nuts.

3. Separate LED driver from canopy by removing (2)

screws.