Alecto DVM2028C Käyttöohje

Alecto Itkuhälytin DVM2028C

Lue alta 📖 käyttöohje suomeksi merkille Alecto DVM2028C (4 sivua) kategoriassa Itkuhälytin. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/4

2 Before use

DVM2028C User’s manual

(For use with DVM2028)

3 Positioning the baby monitor

Caution

• The open box volume of your

parent unit is level , and the 3

maximum volume is level . If 5

you experience feedback noise

from your baby monitor while

positioning:

- Make sure your baby unit and

parent unit are more than 1 meter

apart, OR

- Lower the volume of your parent

unit.

1 Connect and power on the baby unit

Quick start guide

What’s in the box

Kabel minima al 1 meter rwijderd ve

houden van baby.

Garder une dista nce minima l d’un mèt re

du bébé.

Das Kabel ist mindestens 1 Mete von r,

dem Ba , ent t z u halten.by f ern

Keep ca e at leas t 1m from babbl awa y y.

Mantenga el ca e al menos 1 met ro de bl

dista ncia del bebé

V1.1

1. Connect the power adaptor

to the baby unit and a power

supply.

2. Slide the ON/OFF switch to

power on or off your baby unit.

DVM2028C

Commaxx B.V.

Wiebachstraat 37,

6466 NG Kerkrade

The Netherlands,

support.alectobaby.nl

Video baby monitor

Baby unit

V1.0

ATTENTION

Before you start using the set, please remove any

protective foil from the parent unit and baby unit.

Specications

Range:

up to 50 metres indoors

up to 300 metres outdoors

Baby unit power:

5VDC 1000mA power adaptor (incl.)

Model: VT05EEU05100

Frequency: 2405-2475 MHz

Modulation: FSK

RF-power: <20 dBm

Declaration of conformity

Hereby, Commaxx declares that the radio equip-

ment type Alecto DVM2028C is in compliance with

directive 2014/53/EU. The full text of the EU dec-

laration of conformity is available at the following

Internet address: https://commaxx-certiﬁcates.com/

doc/DVM2028C_doc

Use of this equipment is allowed in all countries

of the EU. In France, Italy, Russia and Ukraine, only

indoor use is allowed.

Information power adaptor baby unit:

Manufacturers name and address:

Vtech Telecommunications LTD, 23/F.,

Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road,

Tai Po, Hong Kong.

Model Identiﬁer: VT05EEU05100

Input voltage: 100 - 240V~

Input AC frequency: 50/60 Hz

Output voltage: 5.0V DC

Output current: 1.0 A

Output Power: 5.0 W

Average active efﬁciency: 74.0 %

Efﬁciency at low 10% load: -

No load Power consumption: 0.07 W

Important safety instructions

The applied nameplate is located at the bottom of

the baby unit’s base.

1. CAUTION: Do not install the baby unit at a

height above 2 metres.

2. Use and store the product at a temperature

between 0

oC and 40oC.

Pair a new baby unit

Each newly purchased baby unit ( ) must be paired to your system ( ).DVM2028C DVM2028

NOTESNOTE

• You can pair an additional baby unit to your parent unit. New baby unit must be paired to the

parent unit before use.

• Make sure you power on the parent unit before pairing.

1. Turn on your parent unit and baby unit.

2. Press when the parent unit is idle.

3. Go to > , select .

4. Press and hold the PAIR key for 3 seconds until you hear a “beep”.

5. When the baby unit is successfully paired with your parent unit, the parent unit

displays and the live video.

Overview - Baby unit

1Light sensor

2Baby unit

3Infrared LEDs

4Microphone

5Stand

6 Night light switch

7Temperature sensor

8Pair key hole

• Press and hold for 3 seconds to enter

paring mode.

9Night light

10 Speaker

11 ON/OFF switch

• Slide to turn on or off the baby unit.

12 POWER LED light

• On when the baby unit is turned on

and is paired to the parent unit.

• Flashes when the baby unit is not

being viewed; or when the link to the

parent unit has lost.

13 Power jack

14 Wall mount holes

NOTESNOTE

• Use only the power adaptor supplied with this product.

• Make sure the the baby unit are not connected to an electronically/timer controlled electric power outlet.

• Connect the power adaptor in a vertical or ﬂoor mount position only. The adaptor prongs are not

designed to hold the weight of the baby unit. Otherwise, the adaptor may not properly connect to the

outlets.

• Make sure the the baby unit and the power adaptor cords are out of reach of children.

Mount the baby unit on dry wall (optional) Tips and remarks

INTERFERENCE-FREE:

This baby display monitor is digitally coded. This means you will never receive signals from other devices, nor can the signal from your baby unit(s) be received by e.g. your neighbors.

In case the baby unit(s) or parent unit is placed in or in the close vicinity of electromagnetic ﬁelds, the signal (images or sound) can be slightly affected. If this happens, try a different

location for the baby unit(s) or parent unit or move, if possible, the source of the interference.

EAVESDROPPING/WIRETAPPING:

Eavesdropping/wiretapping of the signals from this baby video monitor is nearly impossible. Not only must one be within range of the baby video monitor, one also needs some very

costly equipment.

MAINTENANCE:

Only clean the baby monitor with a moist cloth; never use chemical cleaners. Before any cleaning, you must disconnect the adaptors.

RANGE:

The baby display monitor has a range of up to 300 meters in an open ﬁeld and up to 50 meters indoors; this range depends on local circumstances.

DELAY IN IMAGES AND SOUND:

Te baby unit transmits the images and sound to the parent unit in digital blocks. The parent unit converts these signals back to a recognizable image

and a comprehensible sound. Therefore, there is a small delay between the moment of movement and making sounds and the display and sounds of the parent unit.

Besides that, the sounds and images on the parent unit are not exactly simultaneous.

Commaxx BV

Wiebachstraat 37

6466 NG Kerkrade

The Netherlands

www.alectobaby.com

Use a pencil to mark two holes in parallel.

Make sure they are the same distance apart

as the wall mount holes on the baby unit.

Adjust the baby unit angle.

Drill two holes in the wall (5.5 mm drill bit). If

you drill the holes into a stud, go to step 3.