Daikin EKBRP2A81 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Daikin EKBRP2A81 (2 sivua) kategoriassa Tuuletin. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
EK
EK
EK
EKEKBR
BR
BR
BRBRP2
P2
P2
P2P2A8
A8
A8
A8A81
1
1
1 1 :
:
:
:: A
A
A
A ABC
BC
BC
BCBC I
I
I
I I/P
/P
/P
/P/P
PR
PR
PR
PRPRIN
IN
IN
ININTE
TE
TE
TETED
D
D
D D C
C
C
CCIR
IR
IR
IRIRCU
CU
CU
CUCUIT
IT
IT
ITIT B
B
B
B BOA
OA
OA
OAOAR
R
R
RRD
D
D
D D KI
KI
KI
KIKIT
T
T
TT
Position the wires so that the cover will not rise when wiring the power supply.
Make sure that the cover is attached securely. If the cover is attached improperly,
electric shocks or fire may result.
●The following two conventions are used to indicate and classify precautions in this manual.
Always read the important safety information provided with them.
●Make sure that the unit operates properly after completing the installation, and explain to the customer
how to operate the unit and keep it maintained.
Also, advise the customer that they should keep this installation manual along with other manual for
future reference.
●At the time of the installation, read the installation manual of the unit along with the electric diagram.
Ask your dealer or qualified personnel to carry out installation work.
Do not attempt to install the air conditioner yourself. Improper installation may result in water leakage,
electric shocks or fire.
0P750596-1
Install the kit in accordance with the instructions in this installation manual.
Improper installation may result in electric shocks or fire.
CAUTION
READ THE INSTRUCTIONS PROVIDED HEREIN CAREFULLY IN ADVANCE AND INSTALL THIS KIT CORRECTLY.
Do not install this kit in the following locations:
１．Where there is a high concentration of mineral oil spray or vapor for example a kitchen.
２．Where corrosive gas, such as sulfurous acid gas, is produced, acid or alkaline steam gathers,
or the air contains a high salt content, such as places by the sea. Parts may be corroded and fall off.
３．Near machinery emitting electromagnetic waves or in places with great voltage fluctuations,
such as factories.
４．Where flammable gas may leak, in places with carbon fiber or ignitable dust suspensions in the air
or with volatile flammables such as paint thinner or gasoline, or in vehicles or vessels.
Fire may result if gas leakage occurs and stays around the kit.
５．Where small animals intrude, fallen leaves gather, or weeds grow.
Small animals making contact with electrical parts can cause malfunctions, smoke or fire.
Turn off the unit before touching electrical parts.
An electric shock may be received if charged parts come in contact with humans.
Failure to observe these instructions properly may result in property damage or
personal injury, which may be serious depending on the circumstances.
Failure to follow these instructions properly may result in personal injury or loss of life
.
WARNING
Be sure to use the specified wires and fix them securely so that no external force resulting from the wires
will be imposed on any terminal connections.
Improper connections or securing of wires may result in abnormal heat build-up or fire.
CAUTION
Make certain that all electrical work is carried out by qualified personnel according to the local laws and
regulations and this installation manual, using a separate circuit.
Insufficient capacity of the power supply circuit or improper electrical construction may lead to electric
shocks or fire.
WARNING
Be sure to use only the specified accessories and parts for the installation work.
Failure to use the specified parts may cause the kit to fail or result in electric shocks or fire.
PLEASE READ THESE "SAFETY PRECAUTIONS" CAREFULLY BEFORE INSTALLING
Accessories
WHITE
1 pc.
Wire harness
assy(2)
ABC I/P printed circuit
board kit
WHITE
Please make sure all the below listed components are
in the package prior to the installation.
Harness clamp Tie wrap
1 pc.1 pc.
Wire harness
assy(1)
Installation
manual
９
For 1fan type
:Remove the screws on the front panel.
:Slightly lift the panel.
:Pull the panel forward and remove it.
:Remove the screws on the front panel(upper).
:Slightly lift the panel.
:Pull the panel forward and remove it.
:Remove the screws on the Electrical Components Box cover.
:Pull the cover downward till its top shows.
:Pull the cover forward and remove it.
８
７
For 2fan type
５
１
・Remove the front panel and Electrical Components Box cover.
２
３
６
４
Before Installation
Installation Method For VRV T,U,A type series.
WHITE(12 pins) WHITE(5 pins)
1 pc. 1 pc.1 pc. 1 pc.
WHITE
WHITE(4 pins)
Wire harness
assy(3)
・Please make sure that the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit board
(X1M(A,B,C)) has at least the specifications mentioned in
the table below.
Transmission Wiring
Voltage 220 - 240 V
Wire type Only use harmonised wire providing double insulation and suitable for
applicable voltage.
Wire size 0.75 - 1.25 mm²
3
2
6
58
9
3
2
6
5
8
9
【In
【In
【In
【In 【In cas
cas
cas
cascase o
e o
e o
e oe of
f
f
f f X66A
X66A
X66A
X66AX66A co
co
co
co conne
nne
nne
nnennecto
cto
cto
ctoctor w
r w
r w
r wr with
ith
ith
ithith 12
12
12
12 12 pin
pin
pin
pin pins.】
s.】
s.】
s.】s.】
【In
【In
【In
【In【In ca
ca
ca
ca case
se
se
se se of
of
of
of of X66A
X66A
X66A
X66AX66A co
co
co
co conn
nn
nn
nnnnect
ect
ect
ectector
or
or
or or with
with
with
withwith 5
5
5
5 5 pin
pin
pin
pinpins.】
s.】
s.】
s.】s.】
【In
【In
【In
【In 【In cas
cas
cas
cascase o
e o
e o
e oe of
f
f
f f X66A
X66A
X66A
X66AX66A co
co
co
co conne
nne
nne
nnennecto
cto
cto
ctoctor w
r w
r w
r wr with
ith
ith
ithith 4
4
4
4 4 pins
pins
pins
pinspins.】
.】
.】
.】.】
:Set the ABC I/P printed
circuit
board
as shown in the right figure.
:Connect the wire harness assy to the ABC I/P
printed circuit board(X1A).
Use only wire harness assy
(3):4 pins
.
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Proceed wiring of the wire harness assy(3) and
transmission wire, as shown in the right figure.
:Connect the wire harness assy(3) to the A1P(X66A).
:Bundle wiring of the wire harness assy(3) at
location shown in the right figure and fasten it
to other wires using tie wrap (field supply)
:Fasten the transmission wire with other wires
using tie wrap.
:Set the ABC I/P printed circuit board
as shown in the right figure.
:Mount harness clamp.
:Connect the wire harness assy(1) to the
ABC I/P printed circuit board(X1A).
Use only wire harness assy(1):12 pins.
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Proceed wiring of the wire harness assy(1) and
transmission wire, as shown in the right figure.
:Connect the wire harness assy(1) to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap.
Step
1
2
Step
3
Step
Step
4
5
Step
Step
6
~
1 6
Step
For 2fan type
Step
X1M
Step
Step
Step
Step
A1P
4
X1A
3
2
Step
Step
6
Step
Step
4
5
Transmission wire
(To Cool/Heat selector)
3
1
4
X66A
Step
4
For 1fan type
StepStep
1
~
:Set the ABC I/P printed
circuit
board
as shown in the right figure.
:Connect the wire harness assy
(1):12 pins
to the
ABC I/P printed circuit board(X1A).
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Connect the wire harness assy(1) to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap.
Step
1
2
Step
3
Step
Step
4
Step
Step
A1P
4
1
3
Transmission wire
(To Cool/Heat selector)
2
X66A
X1A
Step
Step
Step
For 2fan type
Step
61
~
Step
Step
:Set the ABC I/P printed
circuit
board
as shown in the right figure.
:Mount harness clamp.
:Connect the wire harness assy to the ABC I/P
printed circuit board(X1A).
Use only wire harness assy
(2):5 pins
.
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Proceed wiring of the wire harness assy(2) and
transmission wire, as shown in the right figure.
:Connect the wire harness assy(2) to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap.
Step
1
2
6
4
5
Step
3
Step
Step Step
X66A
4
1
3
Transmission wire
(To Cool/Heat selector)
5
4
Step
Step
6
Step Step
2
3
X1A
4
A1P
Step
Step
Step
Step
X1M
1
Step Step
For 1fan type
4
~
Step
:Set the ABC I/P printed
circuit
board
as shown in the right figure.
:Connect the wire harness assy
(2):5 pins
to the
ABC I/P printed circuit board(X1A).
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Connect the wire harness assy(2) to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap.
Step
4
Step
3
1
2
Step
Transmission wire
(To Cool/Heat selector)
Step
Step
A1P
4
1
3
2
X66A
X1A
Step
Step
Step
For 2fan type
Step
61
~
1
Step
Step
2
3
Step
4
Step
5
Step
6
Step
X66A
A1P
X1M
X1A
Transmission wire
(To Cool/Heat selector)
1
Step
2
Step
Step
3
Step
3
Step
3
4
Step
5
Step
Step
6
Installation Metho d (Continued from the left)
(Continued from pre vious page)Installation M ethod
【In
【In
【In
【In【In ca
ca
ca
ca case o
se o
se o
se ose of X6
f X6
f X6
f X6f X66A
6A
6A
6A6A con
con
con
con connect
nect
nect
nectnector
or
or
or or wit
wit
wit
witwith 4
h 4
h 4
h 4 h 4 pin
pin
pin
pinpins.】
s.】
s.】
s.】s.】
Step
2
1
3
Step
4
Step
:Set the ABC I/P printed
circuit
board
as shown in the right figure.
:Connect the wire harness assy
(3):4 pins
to the
ABC I/P printed circuit board(X1A).
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Connect the wire harness assy(3) to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap (field supply).
Step
Step
Step
:Set the ABC I/P printed circuit board
as shown in the below figure.
:Connect the wire harness assy(2) to the ABC I/P
printed circuit board(X1A).
Use only wire harness assy(2):5 pins.
And connect the transmission wiring of the
Cool/Heat selector to the ABC I/P printed circuit
board(X1M(A,B,C)).The tightening torque of
X1M screw is 0.53~0.63N・m(0.39~0.46ft・lbf)
:Proceed wiring of the wire harness assy(2) and
transmission wire, as shown in the below figure.
:Connect the wire harness assy
(2)
to the A1P(X66A).
:Fasten the transmission wire with other wires
using tie wrap.
・Remove the front panel and Electrical Components Box cover.
~
11
5
5
3
Step
4
Step
Installation Metho d
Step
2
Step
Step
Before Installation
:Remove the screws on the front cover.
:Slightly lift the panel.
:Pull the panel forward and remove it.
:Remove the 4 screws on the Electrical Components Box cover.
:Pull the cover downward till its top shows.
:Pull the cover forward and remove it.
４
６
２
５
１
３
X66A
A1P
X66A
A1P
X1A
X1A
Power supply type
575V
Power supply type
208/230V,400V,460V
X1M
X1M
For VRV-W T type series.
2
ON
31
Factory
default
OFF 4
ON
A1P
Setting of the outdoor unit
Control P-board of
the outdoor unit(A1P)
1. Please check after all the procedures are followed to make sure
there is no such connector/terminal in the Electrical Components Box
left disconnected.
2. Put back the Electrical Components Box cover in the reverse way as it was removed.
3. Put back the front panel in the reverse way as it was taken off.
DIP Switch
(DS1)
3
Setting of the outdoor unit when connecting to COOL/HEAT selector.
4
1. Turn on DIP switch (DS1-1)which is located on the control P-board (A1P) of the
outdoor unit before turn on the outdoor unit.
OFF
DS1
2
After Assembli ng
1
DS1
2. Carry out trial operation after turning on the outdoor unit.
For trial operation method, refer to Installation manual of the outdoor unit.
When this kit is used except cool/heat selector,
please refer to installation manuals or engineering data.
When connecting to
COOL/HEAT selector
1
Step Step
For 1fan type
4
~
Transmission wire
(To Cool/Heat selector)
X1A
X1M
A1P
X 6 6 A
Step
1
Step
2
Step
3
4
Step
4
Step
Step
1
Step
2
Step
1
Step
2
Step
3
Step
5
Step
3
Step
5
Step
4
Step
4
Tuotetiedot
| Merkki: | Daikin |
| Kategoria: | Tuuletin |
| Malli: | EKBRP2A81 |
Tarvitsetko apua?
Jos tarvitset apua merkille Daikin EKBRP2A81 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Tuuletin Daikin Käyttöohjeet
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
Tuuletin Käyttöohjeet
- Tuuletin NewAir
- Tuuletin Bosch
- Tuuletin Exquisit
- Tuuletin DeWalt
- Tuuletin Thermex
- Tuuletin Cecotec
- Tuuletin Comfee
- Tuuletin Imarflex
- Tuuletin Kogan
- Tuuletin Koenic
- Tuuletin Westinghouse
- Tuuletin Sencor
- Tuuletin Khind
- Tuuletin Clean Air Optima
- Tuuletin Taurus
- Tuuletin Ryobi
- Tuuletin Brandson
- Tuuletin Ufesa
- Tuuletin Milwaukee
- Tuuletin V-Tac
- Tuuletin Magmatic
- Tuuletin Eldom
- Tuuletin Vonroc
- Tuuletin Modern Fan Co.
- Tuuletin Quorum International
- Tuuletin Signature
- Tuuletin Mystery
- Tuuletin Duracraft
- Tuuletin Mellerware
- Tuuletin Home Electric
- Tuuletin Perfect Aire
- Tuuletin Izzy
- Tuuletin Lasko
- Tuuletin Prime3
- Tuuletin Yamazen
- Tuuletin KDK
- Tuuletin Vornado
- Tuuletin Keystone
Viimeisimmät Tuuletin Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024