Erica Synths Black Joystick2 Käyttöohje
Erica Synths
Näppäimistö
Black Joystick2
Lue alta 📖 käyttöohje suomeksi merkille Erica Synths Black Joystick2 (2 sivua) kategoriassa Näppäimistö. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
BLACK JOYSTICK2
Y 1 Y 2 Y 3 Y 4
X 1 X 2 X 3 X 4
GATE3 GATE4
CH 1
_____
JOYSTICK
CH 2
_____
SINE
CH 3
_____
RND
CH 4
_____
SNEW
RECMODE
CLEAR
BLACK JOYSTICK2
THANK YOU FOR PURCHASING ERICA SYNTHS
BLACK SERIES MODULE!
Erica Black Series include high-end, unique functionality and superior
quality modules. Only the best, highest quality components are used,
all inputs and outputs are protected against undesired overvoltage.
Erica Black Series consist of range of modules that are needed to put
together entire synth. Enjoy!
Erica Synths Black Joystick2 is 8 channel multi functional CV and sound
source – joystick, movement recorder, distinct LFO and drone/noise
oscillator. . It provides great interaction with the modular system and
allows to develop unconventional modulation patterns instantly.
SPECS:
CV output amplitude -5V – +5V
LFO frequency range 0.1Hz – 32Hz
Drone oscillator frequency range 32Hz - 1kHz
Max motion record time 8” per channel
Panel width 12HP
Module depth 30mm
Power consumption 71mA@+12V, 20mA@-12V
FEATURES:
8 simultaneous CV outputs
2 gate outputs
4 motion record channels
Sine and Random LFOs with adjustable
frequency and amplitude
Drone/noise oscillator
Gate record
Two 4-position CV panners
Ski friendly design
An octopus
LEDs
The bicolour LEDs indicate the output CV state. Green means the output is positive, yellow - negative.
Y1; Y2; Y3; Y4
These are CV outputs that correspond to joystick movement along Y axis and these are 90o phase
shifted CV outputs in the LFO mode
GATE
These are the Gate outputs for channels 3 and 4. In Joystick and SNEW modes a +5V signal is present during a motion of the
joystick. In LFO mode and Joystick motion record mode a +5V signal is present when CV is above 0V. This means, you can
record rhythmic gates by moving a joystick vertically. The LEDs are on, when the gate is high. When in sine or random LFO
mode, the Gate output becomes a random trigger generator, when in drone/noise oscillator mode, the Gate output
provides another audio output - squarewave.
JOYSTICK
Move the joystick to control X/Y CV outputs and/or record
the motion of the joystick. In the LFO and Drone Oscillator
mode X movement of joystick changes the frequency, Y
movement – amplitude of the signal on outputs. You can
also record LFO automations – frequency and amplitude
change. When the motion is recorded in a certain channel,
and in the same channel the joystick is moved, the
recording is overridden by the movement momentarily. As
movement stops, the output CVs smoothly fade back to the
recorded motion and playback continues.
CONFIGURATION
There are two configurable options available:
1) joystick position save, when switching to other channel. For example,
you are in SINE mode on channel 1 and you have set a joystick is a
specific position to achieve desired rate/amplitude ratio, and then switch
to the channel 2 and record some automations. If a joystick position save
is NOT engaged, as soon you switch back to the channel 1, the
rate/amplitude ration will be dierent, because the joystick position has
changed. If a joystick position save IS engaged, the rate/amplitude ratio
will remain the same till you move the joystick through the original
position. If you want immediate response from the joystick, we
recommend to turn a joystick position save o; if you want more control
over joystick position settings, turn a joystick position save on.
2) recall of last active channel on powering the module o. If this option is
engaged, the module will save all settings of the last
selected channel and
recall them next time, you power a case on.
X1; X2; X3; X4
These are CV outputs that correspond to joystick movement along X axis and these are primary CV
outputs in the LFO mode
REC
Push and hold the REC button to record a motion of a joystick. Once released the motion will start to play back
automatically. A maximum record time is 8” per channel. You can also record frequency/amplitude automations of the
LFO and drone/noise oscillator. If automation is recoded and plays back, a LED behind the relevant channel button will
be half dimmed until you clear the recording.
MODE
Select one or several channels simultaneously, you wish to initiate one of four action modes, and then push
and hold the MODE button and push one of CHANNEL/MODE buttons to select the output mode. Push and
hold the MODE button and push REC button to clear recorded automations on a selected channel.
CH1; CH2; CH3; CH4/MODE
These are the CHANNEL SELECT and MODE buttons. Push one or several buttons simultaneously to select the
output channel. If several channels are selected simultaneously, you can control parameters on selected
channels simultaneously. Buttons of the selected channels will be lit.
Push and hold the MODE button and push one of the CHANNEL/MODE buttons to select the CV output mode
of the channel. The button of the selected mode will start to blink. Available modes are:
JOYSTICK. In this mode, depending on a joystick position up to -5V to +5V signals are available on X and Y
outputs. You can record up to 8” of a motion of the joystick by pushing and holding the REC button. The
recorded motion will start to loop automatically. To clear the recording push and hold the MODE button and
push the REC button.
SINEWAVE LFO/DRONE OSCILLATOR. In this mode you have low frequency sinewave on the X output and
same, but 90o phase shifted sinewave on the Y output. X position of the joystick defines the frequency of the
sinewave, Y position defines the amplitude. You can record the change of the frequency and amplitude by
pushing and holding the REC button. The recorded motion will start to loop automatically. To clear the
recording push and hold the MODE button and push the REC button. To switch to the DRONE OSCILLATOR
mode (audio frequency sinewave) push and hold the MODE button and push the relevant channel button for
2". The channel button will become 50% dimmed, and next time, you select a channel, it will be in drone
oscillator mode. To turn drone oscillator mode o, push and hold the MODE button and push the relevant
channel button for 2". Try to use all 8 outputs in the Drone oscillator mode! Please note that the sine oscillator is
primarily in intended to work as FM modulation source; as a sound source it may not sound perfect due to
20kHz sampling rate.
RANDOM LFO/NOISE OSCILLATOR. In this mode you have stepped random voltages on the X and Y outputs.
X position of the joystick defines the frequency of the random voltage change, Y position defines the
amplitude. You can record the change of the frequency and amplitude by pushing and holding the REC
button. The recorded motion will start to loop automatically. To clear the recording push and hold the MODE
button and push the REC button. You can swith the NOISE OSCILLATOR mode on/o same way as sine
oscillator.
SNEW PANNER (SOUTH-NORTH-EAST-WEST) . In this mode you have 4x2 CV outputs, each changing from 0V
to +5V. Meaning, if you set the SNEW mode on the CHANNEL1 and CHANNEL2, and Y1 outputs 0-+5V, when the
joystick is mover from the center right (east), X1 outputs 0-+5V, when the joystick is moved from the center up
(north), Y2 outputs 0-+5V, when the joystick is moved from the center to the left (west), X2 outputs 0-+5V, when
the joystick is moved from the center to the down (south). Same works for pair of CHANNEL3 and CHANNEL4.
This is particularly useful for controlling VCAs in quadraphonic performances or controlling several X-faders,
VCAs, VCFs or other modules simultaneously. You can record the motion of the joystick by pushing and
holding the REC button. The recorded motion will start to loop automatically. To clear the recording push and
hold the MODE button and push the REC button.
When operating the Black Joystick2 module you select the CHANNEL, push and hold the MODE button to
check, what MODE is selected – the relevant MODE button will start to blink. When you select a dierent
mode, all reordered automations are instantly cleared.
Transport the instrument carefully, never let it drop or fall
over. Warranty does not apply to modules with visual
damages.
The module has to be shipped in the original packaging
only. Any module shipped to us for return, exchange and/or
warranty repair has to be in its original packaging. All other
deliveries will be rejected and returned to you. Make sure
you keep the original packaging and technical documentation.
This device complies to the EU guidelines and is manufac-
tured RoHS conforming without use of lead, mercury,
cadmium and chrome. Nevertheless, this device is special
waste and disposal in household waste is not recommended.
User manual by Girts Ozolins@Erica Synths.
Design by Ineta Briede@Black8.
Copying, distribution or any commercial use in any way is
prohibited and needs the written permission by Erica Synths.
Specifications are subject to change without notice.In case of
any questions, feel free to contact us through www.erica-
synths.lv.
You will find Erica Synths terms of warranty at
www.ericasynths.lv
Items for return, exchange and/or warranty repair have to
be registered at SUPPORT on www.ericasynths.lv and send
back to us according to instructions in the support page.
SAFETY INSTRUCTIONS
Please follow the instructions for use of the Erica Synths module below,
‘cause only this will guarantee proper operation of the module and
ensure warranty from Erica Synths.
Water is lethal for most of the electric devices, unless they are made
waterproof. This Erica Synths module is NOT intended for use in a
humid or wet environment. No liquids or other conducting
substances must get into the module. Should this happen, the
module should be disconnected from mains power immediately,
dried, examined and cleaned by a qualified technician.
Do not expose the module to temperatures above +50° C or below
-20° C. If you have transported module in extreme low temperatures,
leave it in room temperature for an hour before plugging it in.
In order to access configuration, power a modular case o,
push and hold the MODE button, and power the case on.
Now, you can push CH1 button to engage the joystick position
save and CH2 button to engage recall of last active channel.
If the option is engaged, the relevant channel button will be lit.
Tuotetiedot
| Merkki: | Erica Synths |
| Kategoria: | Näppäimistö |
| Malli: | Black Joystick2 |
Tarvitsetko apua?
Jos tarvitset apua merkille Erica Synths Black Joystick2 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Näppäimistö Erica Synths Käyttöohjeet
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
Näppäimistö Käyttöohjeet
- Näppäimistö Kogan
- Näppäimistö GoGEN
- Näppäimistö Gembird
- Näppäimistö RGV
- Näppäimistö Goodis
- Näppäimistö EVOLVEO
- Näppäimistö Xtrfy
- Näppäimistö Ducky
- Näppäimistö Xtech
- Näppäimistö Mad Dog
- Näppäimistö Voxicon
- Näppäimistö UNYKAch
- Näppäimistö Carlsbro
- Näppäimistö Accuratus
- Näppäimistö Gamesir
- Näppäimistö NGS
- Näppäimistö Kurzweil
- Näppäimistö Keychron
- Näppäimistö Rapoo
- Näppäimistö Savio
Viimeisimmät Näppäimistö Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
22 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024