Leviton 49990-LDL Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Leviton 49990-LDL (11 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/11
PK-A3141-10-02-5A
(REF-0R-49990-00 -06)-00
,>?@=04-0=!;?4.:990.?:=
%! &!$
%&
%%&
%
%
%%


%


%
%&R! &!$
A Division of Leviton Manufacturing Co.,Inc.
Technical Support: 800-824-3005
Fax: (425) 483-5270
www.levitonvoicedata.com
Description Part No.
Multimode ST Connector 50/125 & 62.5/125 49990-MST
Singlemode ST Connector 49990-SST
Multimode SC Connector 50/125 & 62.5/125 (beige) 49990-MSC
LO Multimode SC Connector (aqua) 49990-LSC
Singlemode SC Connector (blue) 49990-SSC
SC Duplex Clip, black (Bag of 25) 49886-DSC
Mulimode LC Connector with 3mm boot (beige) 49990-ML2
LO Multimode LC Connector with 3mm boot (aqua) 49990-LL2
Singlemode LC Connector with 3mm boot (blue) 49990-SL2
Multimode LC Connector with .9mm boot (beige) 49990-MDL
LO Multimode LC Connector with .9 mm boot (aqua) 49990-LDL
Singlemode LC Connector with .9mm boot (blue) 49990-SDL
LC Duplex Clip, Multimode, beige (bag of 25) 49886-DLM
LC Duplex Clip, Singlemode, blue (bag of 25) 49886-DLS
Fast Cure Tool Kit 49800-FTK
Fast Cure Consumables Kit 49800-FCC
Adhesive Primer Kit 49800-680
Crimp Tool with .128, .151, .178 hex die 49886-FCT
Replacement Needles (19 gauge, bags of 25) 49886-FCN
Syringes (bags of 25) 49886-SYR
LC Polishing Puck 49886-LCP
LC Duplex Scope Adapter 49886-LCD
LC Simplex Scope Adapter 49886-LCS
Fast Cure Carrying Case 49886-FCC
Part Numbers
! &!$
PK-A3141-10-02-5A
(REF-0R-49990-00- 06)00-

%&%)&

)&

'$

>>08-7D9>?=@.?4:9>
"$"$
77:990.?:=&D;0>
NOTE: If using 900 µm buffered fiber, do not use the crimp tube in step 1.
1. Slide the boot and the crimp tube onto the fiber, with the small end inserted first. (Figure 1)
:=88,.60?0/,-70Use the ribbed boot, provided.
:=S8@110=0/,-70Use the smooth boot, provided.
NOTE: If using an SC Connector on 900µm buffered fiber, you must install the SC body into the housing
before continuing to step 2. Align the body with the connector housing, then insert the body into
the housing until it snaps into place. Use the dust cap to push the body into the housing.
2. Strip the jacket and/or buffer using the measurements provided in the chart below, and strip in
increments of 1/4”. If using jacketed cable, trim the aramid strands as indicated, below.
(Figure 2a-c)
!&&:307;,A:4/?::7-@110=,9/14-0=.:9?,849,?4:9.70,95,.60?,9/0C;:>0/-@110=B4?3
,,7.:3:7B4;0?309B4?3,749?1=00B4;0-:?3-01:=0,9/,1?0=>?=4;;492
3. Clean exposed fiber with a 99% alcohol wipe followed by a lint-free wipe to remove any contaminants.
 !&8,20>,=09:??:>.,70
%:990.?:=&D;0>:988,.60?0/,-70! +
4. Insert spacer over buffer and push all the way down, until it rests against the jacket. (Figure 3)
7409? :?0> :?0>/07W@?474>,?0@= :?,>/07@>@,=4:
strip length 20 mm
1/4
1/4
3/4
1 3/4
1/2
1 1/2
apply primer 10mm
 !&8,20>,=09:??:>.,70
PK-A3141-10-02-5A
(REF-0R-49990-00- 06)00-
%%
77:990.?:=,9/4-0=&D;0>
1. Remove the dust cap from the connector.
2.
2.
2.
2.2. Dry fit the fiber by inserting the fiber into the connector. This will assure that all coating has been
removed and the fiber can be inserted into the connector ferrule.
3. Shake the adhesive bottle before using. Remove the cap from the adhesive bottle, and attach the
needle by pressing it gently onto the top of the bottle until you feel it set into place.
NOTE: Syringes are also available for inserting adhesive.
4. Insert the needle and firmly hold it against the back of the connector while filling it. Being careful not to
overfill the connector, squeeze the bottle gently, injecting the adhesive into the connector. Continue
until a dot of adhesive is visible at the other end, then remove the needle. Wipe away excess adhesive
from the end of the ferrule.
5. Using the brush attached to the lid on the bottle of primer, apply the primer to the first 10mm of the
exposed fiber. See figure 2a.
6. Insert the fiber into the back of the connector. To prevent premature bonding, use continuous motion,
until the fiber is fully seated in the connector. The primer will activate adhesive and begin the bonding
process.
!&&3014-0=>3:@7/-049>0=?0/B4?349>0.:9/>:1;=48492
7. Hold the fiber in place for 10-20 seconds, and allow up to 3 minutes for the adhesive to bond.
8. If using any cable type but jacketed fiber, slide the boot back up over the back of the connector, now. If
using jacketed fiber, follow the steps, below.
//4?4:9,7%?0;>:=88,.60?0/,-70! +
9. Arrange the aramid strands evenly around the end of the connector, then slide the crimp tube over the
aramid strands and connector. Using a crimp tool, crimp the tube at both the large end (step 1) and the
small end (step 2). (Figure 4)
%&%7,=2009/Use the .178” hex die.
%&%>8,7709/Use the .151” hex die.
Use the .128” hex die.
7409? :?0> :?0>/07W@?474>,?0@= :?,>/07@>@,=4:


Tuotetiedot

Merkki: Leviton
Kategoria: Ei luokiteltu
Malli: 49990-LDL

Tarvitsetko apua?

Jos tarvitset apua merkille Leviton 49990-LDL esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Leviton Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet