Leviton 4999K-YLC Käyttöohje
Leviton
Ei luokiteltu
4999K-YLC
Lue alta 📖 käyttöohje suomeksi merkille Leviton 4999K-YLC (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
For more information please contact tech support at: 1-800-824-3005 or visit: www.leviton.com
3
2
1
NOTE: 900um boots are sold separately.
4999K-*LC
SKLC (Secure Keyed LC) Connector Field Termination
ASSEMBLY INSTRUCTIONS
5. Using the brush attached to the lid on the bottle of primer, apply the primer to the
area of ber as indicated. See (FIGURE 2).
6. Insert the ber into the back of the connector. To prevent premature bonding, use
a continuous motion, until the ber is fully seated in the connector. The primer will
activate the adhesive and begin the bonding process.
NOTE: The ber should be inserted within 45 seconds of placing the primer on the ber.
7. Hold the ber in place for 10-20 seconds, and allow up to 3 minutes for the
adhesive to fully bond.
8. Slide the boot back up over the back of the connector.
CLEAVE AND POLISH
1. When the adhesive is cured (no longer wet), scribe the ber where it meets the
bead of adhesive at the end of the ferrule. (FIGURE 3)
2. Pull the ber away from the connector, properly dispose of the debris.
NOTE: Loose ber debris can be dangerous. Be sure to properly dispose of ber
debris.
3. Begin by “air polishing” the connector with 12μm polishing film. Leviton’s 12 μm
lm is a dark pink in color. Hold the edge of the lm, with thumb and fore nger,
dull side down. Hold the connector ferrule pointing up. Gently touch the connector
to the lm. While holding the polishing lm in contact with the connector, move the
polishing lm in approximately a 1 inch circle to remove the ber stub. The
scraping sound of the ber on the lm will cease when the air polish process is
complete.
PREPARE
1. Slide boot onto the ber, with the small end inserted rst, away from the
connector. (FIGURE 1)
NOTE: 900um boots are sold separately.
2. Remove 4 inches of the outer cable sheath for jacketed cable.
3. Strip the 900μm buffer as indicated in the measurements provided in the chart
below (FIGURE 2)*, strip the fiber in increments of ¼”.
4. Clean exposed ber with a lint-free wipe damped with 99% isopropyl alcohol to
remove any contaminants.
NOTE: Images are not to scale.
ASSEMBLE
1. Remove the dust cap from the connector.
2. Dry t the ber by inserting the ber into the connector. This will assure that
all coating has been removed and the ber can be inserted into the connector
ferrule.
3. Shake the adhesive bottle before using. Remove the cap from the adhesive
bottle, and attach the needle by pressing it gently onto the top of the bottle
until you feel it set into place.
NOTE: Syringes are also available for inserting adhesive. See parts list for part
number.
4. Insert the needle into the back of the connector, holding it rmly in place while
lling. Being careful not to over ll the connector, squeeze the bottle gently,
injecting the adhesive into the connector. Continue squeezing until a dot of
adhesive is visible at the ferrule end of the connector, and then remove the
needle. Wipe away any excess adhesive from the end of the ferrule.
4. Hold a lint-free wipe across the nger tips, and then gently press the ferrule
end-face against the wipe. Twist the connector in place to remove any debris.
Do not drag the connector across the lint-free wipe.
5. Wipe the bottom surface of the LC 1.25mm polishing puck and the surface of
the polishing pad with a lint-free wipe damped with 99% isopropyl alcohol to
remove any contaminants.
6. Place the 3μm film on the polishing pad, dull side up. Leviton’s 3μm film is
yellow in color. Place the polishing puck on the lm. Gently insert the
connector ferrule into the polishing puck and using very light pressure, trace 15-
20 figure 8’s on the lm. Inspect to ensure the ber is polished ush by rst
gently dragging the connector across a lint-free wipe. Fiber should not snag. If
the ber snags, continue polishing until it does not snag. Remove debris with a
lint-free wipe dampened with 99% isopropyl alcohol.
7. Repeat steps 5 and 6 with 0.3μm polishing film. Leviton’s 0.3μm film is a light
blue in color.
8. Using a Leviton 200x inspection scope, inspect the ber core to assure the core
is not scratched, cracked, broken and is clean. (FIGURE 4)
9. Replace the dust cap on the connector to maintain cleanliness.
INSPECTING THE BACKLIT FIBER:
SCRIBE AND PULL FIBER AWAY
Multimode 62.5/125 Singlemode 9/125
4
White area must be free
of all obstruction. Grey
area should be free of
scratches and dark
spots.
ALL BUFFERED CABLE
PK-93775- - -10 02 0A
For more information please contact tech support at: 1-800-824-3005 or visit: www.leviton.com
IMPORTANT INSTRUCTIONS
1. Read and understand all instructions. Follow all warnings and instructions marked on the product.
2. Do not use this product near water-e.g., near a tub, wash basin, kitchen sink or laundry tub, in a
wet basement, or near a swimming pool.
3. Never push objects of any kind into this product through openings, as they may touch dangerous
voltage s.
4. SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION
1. Never install communications wiring or components during a lightning storm.
2. Never install communications components in wet locations unless the components are designed
specically for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network
interface.
4. Use caution when installing or modifying communications wiring or components.
5. To prevent electrical shock, each opening must be lled with a module.
5
6
8
7
10
INSTALLING THE SECURED KEYED LC HOUSING
NOTE: Assure correct connector polarity prior to nal assembly of the housing; refer
to (FIGURE 5). Failure to do so may result in the need to disassemble the
Secured LC housing, which will result in damage to the housing.
1. Place the upper housing with the top of the housing down on the work surface
(FIGURE 6).
2. Insert the rst ber connector, with the LC latch facing down, into the correct
connector slot in the upper housing, making sure the retention slots on the
connector are aligned with the capture feature in the housing (FIGURE 7).
3. Now insert the second fiber connector, with the LC latch facing down, into the correct
connector slot in the upper housing, making sure the retention slots on the
connector are aligned with the capture feature in the housing (FIGURE 8).
4. Insert the Assembly Alignment Guide into the lower housing, from the bottom
(FIGURE 9).
5. Place the lower housing over the upper housing with the Assembly Alignment Guide
positioned so it will t into the alignment slot into the upper housing (FIGURE 10).
6. Place the housing assembly between your thumb and ngers, gently squeeze the
upper and lower housing assemblies together until the retention snaps lock the
upper and lower housing together.
7. Remove the Assembly Alignment Guide from the connector housing.
NOTE: Always inspect the ber connector before inserting into an adapter. Leviton
200x scope with duplex adapter is specically designed to allow inspection
of duplex connector pairs.
NOTE: Once a connector is engaged into an adapter, an extraction tool of the
same keyed color is required to disengage from the adapter
FIBER STRAND POLARITY
Proper polarity of the ber strands is required to assure transmit and receive
functionality. See gure 5.
The numbered strands (i.e. 1, 3, 5,) of the fiber cable typically are placed in odd
the A polarity position. The numbered strands (i.e. 2, 4, 6,) of the ber cable even
typically are placed in the B polarity position. This should result in proper A-B
polarity alignment.
Secure Keyed LC Kits & Accessories
Part No.
Secure Keyed LC Connector Kit, 900um, MM/SM - black
4999K
ELC
Secure Keyed LC Connector Kit, 900um, MM/SM - green
4999K
VLC
Secure Keyed LC Connector Kit, 900um, MM/SM - blue
4999K
LLC
Secure Keyed LC Connector Kit, 900um, MM/SM - orange
4999K
OLC
Secure Keyed LC Connector Kit, 900um, MM/SM - red
4999K
RLC
Secure Keyed LC Connector Kit, 900um, MM/SM - slate
4999K
GLC
Secure Keyed LC Connector Kit, 900um, MM/SM - white
4999K
WLC
Secure Keyed LC Connector Kit, 900um, MM/SM - yellow
4999K
YLC
900μm Boot, Blue (bag of 50)
4999K
BLU
900μm Boot, Beige (bag of 50)
4999K
BGE
900μm Boot, Black (bag of 50)
4999K
BLK
900μm Boot, Aqua (bag of 50)
4999K
AQU
Extraction Tool with Dust Cap
ETRTN
*TL
* = W (white), Y (yellow), O (orange), R (red), L (blue), V (green), G (slate), E (black)
Fiber Installation Tools
Part No.
Fast Cure Tool Kit
49800
FTK
Adhesive Primer Kit
49800
680
Fast Cure Consumables Kit
49800
FAC
200x Fiber Inspection Scope
49886
FSP
Duplex LC Scope Adapter (for use with Leviton 200x Scope)
49886
LCD
LC Polishing Puck
49886
LCP
Fast Cure Carrying Case
49886
FCC
Replacement Needles
49886
FCN
Syringes (bag of 25)
49886
SYR
INSIDE
OF TOP
HOUSING
9
PK-93775- - -10 02 0A
Tuotetiedot
Merkki: | Leviton |
Kategoria: | Ei luokiteltu |
Malli: | 4999K-YLC |
Tarvitsetko apua?
Jos tarvitset apua merkille Leviton 4999K-YLC esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu Leviton Käyttöohjeet
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
Ei luokiteltu Käyttöohjeet
- Ei luokiteltu Whirlpool
- Ei luokiteltu Jocel
- Ei luokiteltu BEKO
- Ei luokiteltu Apc
- Ei luokiteltu DeWalt
- Ei luokiteltu Siemens
- Ei luokiteltu Hama
- Ei luokiteltu Neewer
- Ei luokiteltu Danby
- Ei luokiteltu Gigabyte
- Ei luokiteltu Gree
- Ei luokiteltu Hazet
- Ei luokiteltu Philips
- Ei luokiteltu Topeak
- Ei luokiteltu IFM
- Ei luokiteltu Avantree
- Ei luokiteltu Schwaiger
- Ei luokiteltu IKEA
- Ei luokiteltu AeroCool
- Ei luokiteltu Samsung
- Ei luokiteltu Garmin
- Ei luokiteltu StarTech.com
- Ei luokiteltu Imarflex
- Ei luokiteltu Edgestar
- Ei luokiteltu Audient
- Ei luokiteltu McIntosh
- Ei luokiteltu Venom
- Ei luokiteltu Legrand
- Ei luokiteltu Cudy
- Ei luokiteltu Candy
- Ei luokiteltu Axis
- Ei luokiteltu Liebherr
- Ei luokiteltu Carson
- Ei luokiteltu Gourmetmaxx
- Ei luokiteltu Truelife
- Ei luokiteltu ETA
- Ei luokiteltu Lindy
- Ei luokiteltu HP
- Ei luokiteltu Pioneer
- Ei luokiteltu Summit
- Ei luokiteltu EarFun
- Ei luokiteltu Ecler
- Ei luokiteltu Digitus
- Ei luokiteltu Panasonic
- Ei luokiteltu Unicol
- Ei luokiteltu Audio-Technica
- Ei luokiteltu Toa
- Ei luokiteltu Vox
- Ei luokiteltu Pyle
- Ei luokiteltu Lenovo
- Ei luokiteltu Noctua
- Ei luokiteltu Schneider
- Ei luokiteltu Kindermann
- Ei luokiteltu Anker
- Ei luokiteltu Privileg
- Ei luokiteltu Fluval
- Ei luokiteltu Heatit
- Ei luokiteltu Ryobi
- Ei luokiteltu Kodak
- Ei luokiteltu Sharkoon
- Ei luokiteltu DataVideo
- Ei luokiteltu RGV
- Ei luokiteltu Guzzanti
- Ei luokiteltu Bluesound
- Ei luokiteltu Aplic
- Ei luokiteltu Speco Technologies
- Ei luokiteltu Tripp Lite
- Ei luokiteltu Infiniton
- Ei luokiteltu Smart-AVI
- Ei luokiteltu AXESS
- Ei luokiteltu DAB
- Ei luokiteltu Blaupunkt
- Ei luokiteltu NEP
- Ei luokiteltu Ansmann
- Ei luokiteltu Einhell
- Ei luokiteltu Planet
- Ei luokiteltu Fezz
- Ei luokiteltu Fuxtec
- Ei luokiteltu JBL
- Ei luokiteltu DeepCool
- Ei luokiteltu Kali Audio
- Ei luokiteltu Chief
- Ei luokiteltu Majority
- Ei luokiteltu Helix
- Ei luokiteltu Elation
- Ei luokiteltu Magmatic
- Ei luokiteltu Zendure
- Ei luokiteltu Logilink
- Ei luokiteltu Majestic
- Ei luokiteltu Soundstream
- Ei luokiteltu PAC
- Ei luokiteltu Xaoc
- Ei luokiteltu Hohner
- Ei luokiteltu Britax
- Ei luokiteltu Steiner
- Ei luokiteltu Vonroc
- Ei luokiteltu Bellari
- Ei luokiteltu Rolls
- Ei luokiteltu Ordo
- Ei luokiteltu Ground Zero
- Ei luokiteltu OnePlus
- Ei luokiteltu CRUX
- Ei luokiteltu Karma
- Ei luokiteltu Ridem
- Ei luokiteltu Glemm
- Ei luokiteltu StarIink
- Ei luokiteltu HomeCraft
- Ei luokiteltu Nostalgia
- Ei luokiteltu GameDay
- Ei luokiteltu X-Lite
- Ei luokiteltu Söll
- Ei luokiteltu Sparkle
- Ei luokiteltu Edouard Rousseau
- Ei luokiteltu Caberg
- Ei luokiteltu Exped
- Ei luokiteltu Igloo
- Ei luokiteltu Heusinkveld
- Ei luokiteltu KED
- Ei luokiteltu EPEVER
- Ei luokiteltu Grothe
- Ei luokiteltu Cane Creek
- Ei luokiteltu Swiss Eye
- Ei luokiteltu SilverStone
- Ei luokiteltu Dreame
- Ei luokiteltu Foreo
- Ei luokiteltu Tesla
- Ei luokiteltu Aquael
- Ei luokiteltu Klarstein
- Ei luokiteltu Lauten Audio
- Ei luokiteltu Toddy
- Ei luokiteltu Lexivon
- Ei luokiteltu Icy Dock
- Ei luokiteltu Elta
- Ei luokiteltu ASI
- Ei luokiteltu Gurari
- Ei luokiteltu Varia
- Ei luokiteltu SPL
- Ei luokiteltu I-Tec
- Ei luokiteltu Xigmatek
- Ei luokiteltu Storcube
- Ei luokiteltu Tracer
- Ei luokiteltu Shark
- Ei luokiteltu REMKO
- Ei luokiteltu Phanteks
- Ei luokiteltu EnOcean
- Ei luokiteltu EK Water Blocks
- Ei luokiteltu Hoymiles
- Ei luokiteltu Envertech
- Ei luokiteltu Cougar
- Ei luokiteltu Asrock
- Ei luokiteltu Audiotec Fischer
- Ei luokiteltu Furman
- Ei luokiteltu Cata
- Ei luokiteltu Radial Engineering
- Ei luokiteltu Hamilton Beach
- Ei luokiteltu Craftsman
- Ei luokiteltu Edesa
- Ei luokiteltu Lowell
- Ei luokiteltu IPGARD
- Ei luokiteltu Libec
- Ei luokiteltu Silver Cross
- Ei luokiteltu American DJ
- Ei luokiteltu Profoto
- Ei luokiteltu Black Lion Audio
- Ei luokiteltu Puls Dimension
- Ei luokiteltu Wasp
- Ei luokiteltu Gamewright
- Ei luokiteltu Claypaky
- Ei luokiteltu Premier Mounts
- Ei luokiteltu MuxLab
- Ei luokiteltu Oppo
- Ei luokiteltu Impact
- Ei luokiteltu Heritage Audio
- Ei luokiteltu Safco
- Ei luokiteltu Monoprice
- Ei luokiteltu Stabila
- Ei luokiteltu CTA Digital
- Ei luokiteltu HammerSmith
- Ei luokiteltu Cyrus
- Ei luokiteltu ATen
- Ei luokiteltu Bialetti
- Ei luokiteltu Xlyne
- Ei luokiteltu Plant Craft
- Ei luokiteltu Sungrow
- Ei luokiteltu Grundfos
- Ei luokiteltu Bazooka
- Ei luokiteltu Carlsbro
- Ei luokiteltu MoFi
- Ei luokiteltu Blackburn
- Ei luokiteltu Bang And Olufsen
- Ei luokiteltu Cowon
- Ei luokiteltu Horizon Fitness
- Ei luokiteltu Jilong
- Ei luokiteltu Gamesir
- Ei luokiteltu Yaesu
- Ei luokiteltu Concept2
- Ei luokiteltu CTOUCH
- Ei luokiteltu RCF
- Ei luokiteltu Microchip
- Ei luokiteltu WilTec
- Ei luokiteltu Wimberley
- Ei luokiteltu Playtive
- Ei luokiteltu Vimar
- Ei luokiteltu Osprey
- Ei luokiteltu Hosa
- Ei luokiteltu Havis
- Ei luokiteltu Emerson
- Ei luokiteltu Biltema
- Ei luokiteltu Bogen
- Ei luokiteltu Electro Harmonix
- Ei luokiteltu Chrome-Q
- Ei luokiteltu Galaxy Audio
- Ei luokiteltu Altman
- Ei luokiteltu Aiphone
- Ei luokiteltu Atlas
- Ei luokiteltu Graco
- Ei luokiteltu MARTOR
- Ei luokiteltu Mean Well
- Ei luokiteltu Exelpet
- Ei luokiteltu Trendnet
- Ei luokiteltu G-Technology
- Ei luokiteltu CubuSynth
- Ei luokiteltu Infasecure
- Ei luokiteltu SecureSafe
- Ei luokiteltu Intellinet
- Ei luokiteltu Hikoki
- Ei luokiteltu Butler
- Ei luokiteltu Texas
- Ei luokiteltu ProfiCook
- Ei luokiteltu Arovec
Viimeisimmät Ei luokiteltu Käyttöohjeet
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024