Luxul XMS-1208P Käyttöohje

Luxul Kytkin XMS-1208P

Lue alta 📖 käyttöohje suomeksi merkille Luxul XMS-1208P (8 sivua) kategoriassa Kytkin. Tämä opas oli hyödyllinen 12 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/8
READ ME FIRST
QUICK INSTALL GUIDE
12-Port/8 PoE+ Gigabit
Managed Switch
XMS-1208P
Includes:
XMS-1208P 12-Port/8 PoE+ Switch
Rack Mount Kit
Rubber Feet
Power Cord
INSTALLATION AND SETUP
1
Physical Installation
The XMS-1208P can easily be installed in a standard 19” rack. Two mounting ears
are included for installing and stabilizing the switch. When attaching the mounting
ears and installing the switch in a rack, please refer to the following illustration:
Rack-mounting the XMS-1208P
Use the included screws to attach the mounting ears to each side
of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the
switch is level and properly secured in the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the XMS-1208P.
2Connecting Ethernet and Power
Ethernet and Power Connections
Use one of the ten Ethernet ports to connect the XMS-1208P to any Ethernet-
enabled device, including servers, routers, or other switches. No crossover cable
is necessary.
The XMS-1208P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-8 are PoE+ and
are enabled by default. Ports 9 and 10 are Gigabit Ethernet only (non PoE),
while ports 11 and 12 are Gigabit SFP ports.
Use the included power cable to connect the XMS-1208P to a surge-
protected outlet. The AC input socket is on the rear panel. The built-in
power supply supports 100~240VAC at 50-60Hz.
Network Cabling
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
If you intended to use optical fiber to extend the network beyond the 300-
foot limit of twisted pair Ethernet, SFP modules are required (not included).
cCAUTION: Multiple Uplink channels can create loops, resulting in
network failure. Ensure only one Uplink channel exists
between switches or between the XMS-1208P and a router.
nNOTE: When powering up, the port LEDs may take a moment to
initialize. This is normal as the XMS-1208P initialization and
startup sequence completes.
nNOTE: The XMS-1208P has an internal 130W power supply. Do not
exceed 25.5W each or 130W combined consumption of all
external PoE devices.

Tuotetiedot

Merkki: Luxul
Kategoria: Kytkin
Malli: XMS-1208P

Tarvitsetko apua?

Jos tarvitset apua merkille Luxul XMS-1208P esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Kytkin Luxul Käyttöohjeet

Luxul

Luxul XMS-5248P Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul AMS-2624P Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul XGS-1005 Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul AGS-1008M Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul XMS-1208P Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul XMS-7048P Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul AMS-2600 Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul AGS-1016 Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul XMS-2624P Käyttöohje

14 Tammikuuta 2025
Luxul

Luxul AMS-1816P Käyttöohje

14 Tammikuuta 2025

Kytkin Käyttöohjeet

Viimeisimmät Kytkin Käyttöohjeet

Cudy

Cudy FS1024 Käyttöohje

9 Huhtikuuta 2025
Lancom

Lancom GS-2426P Käyttöohje

5 Huhtikuuta 2025
Lancom

Lancom GS-2412 Käyttöohje

4 Huhtikuuta 2025
Lancom

Lancom GS-2412P Käyttöohje

4 Huhtikuuta 2025
Lancom

Lancom GS-2426 Käyttöohje

4 Huhtikuuta 2025
Hager

Hager ARF970D Käyttöohje

3 Huhtikuuta 2025
Hager

Hager ARF920D Käyttöohje

3 Huhtikuuta 2025
Roline

Roline 14.01.3579 Käyttöohje

2 Huhtikuuta 2025