SoundTube WLL-RX1p-II Käyttöohje

SoundTube Vastaanotin WLL-RX1p-II

Lue alta 📖 käyttöohje suomeksi merkille SoundTube WLL-RX1p-II (4 sivua) kategoriassa Vastaanotin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/4

1.855.663.5600 | mseaudio.com | soundtube.com

Front Rear

Transmitter Box Contents

1- WLL-TX1 wireless transmitter

1- Power supply

Output: 5VDC 1.2A

2- Half rack mount adapters

2- Antenna

TX unit- Transmitter TX unit- Transmitter

RX unit- Receiver/Amp RX unit- Receiver/Amp

TX unit- Transmitter

RX unit- Receiver/Amp

Antenna (4)

Receiver Box Contents

1- WLL-RX1p wireless receiver/amp unit

1- Power supply

Output: 32VDC 3.75A

2- Half rack mount adapters

2- Antenna

2- Two-pin Euro-block connectors

FCC ID: XCO-HSWLLT IC:7756A-HSWLLT

Avis

Les produits SoundTube doit être installé par un installateur professionnel audio/contractuer.

Pour plus de sûreté et pour des performances audio optimales, l'installateur doit suivre toutes

les instructions émises par SoundTube.

Warning

SoundTube products must be installed by a professional audio installer/contractor. For safety

and for optimum audio performance, installer must follow all directions issued by SoundTube.

-II

WLL-TR-1p-II

Install Instructions For:

WLL-TR-1p-II (WLL-TX1-II transmitter and WLL-RX1p-II receiver/amp).

1. Remove unit from box.

8. For best results, Transmitter and

Receiver antennas should face the

same direction (either vertically or

horizontally).

7. Set INPUT sensitivity switch at

0 dB for normal use. If using a

high output source, set the switch

to -6dB.

6. Set RF power switch. Two

options are available, High (H) and

Low (L). The High setting is

recommended for maximum

distance. The low setting is for

installations where 2 or more

TX-1’s are on the same channel

within 60-70 ft of each other.

5. Set input switch to match the

desired input source.

2. Determine location for

placement of WLL-TX1-II. The

WLL-TX1-II may be installed in an

equipment rack (half rack adapter

required) or on a shelf.

-II

4. If desired, the variable LINE

OUT mini jack can be connected

to an external device such as an

ADA hearing assistance system.

3. Connect desired input source to

rear panel. You may use balanced

(1/4” TRS) connectors, unbalanced

mini or USB. Multiple sources may

be connected but only the source

selected on the input switch (step

5) will be sent to the transmitter.

When connecting through the USB

input do not connect an input to

the balanced or line in.

11. After installation of

WLL-RX1p-II unit(s), apply power

to WLL-TX1-II. Adjust front panel

gain knob as needed. The gain

control will adjust the level of both

the input audio and the LINE OUT

feed.

10. On front panel, select transmit

channel 1, 2 or 3. NOTE: the

WLL-RX1p-II unit(s) must be set on

the same channel.

9. Connect power supply to DC IN

5V connector.

12. Done!

(The LED on the front panel will

be red when power is applied to

the TX unit. It will turn blue when

the TX unit is in communication

with the RX).

WLL-TX1-II Install Instructions

-II

Installation Notes: 2a: an installation that puts the WLL-TX1-II in line-of-sight with the WLL-RX1P-II will provide the best results. 2b: Do not install transmitter

more than 230 feet (70 meters line of site or 50 meters indoors) from the desired receiver location(s). 3a: If using the USB input, the WLL-TX1-II will appear as

an audio device on your computer’s control panel.

WLL-TR-1p-II

Install Instructions For:

WLL-TR-1p-II (WLL-TX1-II transmitter and WLL-RX1p-II receiver/amp).

1. Remove unit from box.

8. Select either the Stereo or Mono

operation mode via the selector

switch on the front panel.

7. Connect the power supply to

the DC IN 32V power connector.

6. For best results, Transmitter

and Receiver antennas should

face the same direction (either

vertically or horizontally).

5. If desired, a xed LINE OUT audio

signal is provided by the stereo mini

jack for operating a device such as an

ADA hearing assistance system.

2. Determine location for

placement of WLL-RX1p-II. The

WLL-RX1p-II may be installed in

an equipment rack (half rack

adapter required) or on a shelf.

The antennas may be remoted

using a wi antenna cable (not

included; available through third

party vendors).

4. If desired, a direct audio source

can be connected to the

WLL-RX1p-II via the mini “LINE IN”

jack. Note: If an audio source is

connected to this input, it will

interrupt any RF feed being sent

via the WLL-TX1-II.

3. Connect 4 ohm or 8 ohm

speakers to the L and R channel

output leads using the Euroblock

connectors and push into place in

the appropriate SPEAKER OUT

locations. Alternatively, speakers

may be connected via ¼” plugs at

the L and R “SPEAKER OUT” jacks

to the right of the Euroblock

connectors. Do not connect both.

Be certain to check for the correct

connection polarity.

11. Done!

10. Apply power to unit. Adjust front

panel gain control as needed.

9. Select the receiving channel 1, 2

or 3 on the front panel. NOTE: the

WLL-TX1-II must be set on the

same channel.

Note: If the signal appearing at the receiver is intermittent or noisy, (a) make sure the transmitter’s RF Gain switch is on High; (b) change the location of the

transmitter and/or receiver for line-of-sight position with one another; (c) place the antennas in a line-of-sight position using an antenna extension cable

(available from third party vendors).

WLL-RX1p-II Install Instructions

-II

Installation Notes: 2a: an installation that puts the WLL-TX1-II in line-of-sight with the WLL-RX1p-II will provide the best results. 2b: Do not install transmitter