VTech VC7002 Käyttöohje
VTech
Valvontakamera
VC7002
Lue alta 📖 käyttöohje suomeksi merkille VTech VC7002 (2 sivua) kategoriassa Valvontakamera. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has instructions on how to set
up and register your new sensor.
For instructions on sensor settings, see
the user’s manual that came with your ULE
compatible products. Visit
www.vtechphones.com/wireless-monitoring
for a list of the latest ULE compatible
products.
You may also view or download the online
User’s manual of the respective product
for a full set of installation and operation
instructions at www.vtechcanada.com.
Before use
Install batteries to the
Open/Closed Sensor
NOTES
Use 2 x AAA batteries. Alkaline batteries are
recommended. If you use other kind of batteries,
the performance of the sensor varies.
Do not mix old and new batteries. Do not
mix alkaline, standard (Carbon-Zinc) or
rechargeable (Ni-Cad, Ni-Mh, etc) batteries.
While you insert the batteries, make sure the
polarities are correct.
The batteries operate properly under the
temperature between 0°F (-18°C) and 130°F
(55°C).
Press the latch button on the sensor to
open the battery compartment case.
Insert two AAA alkaline batteries into the
battery compartment.
•
•
•
•
1.
2.
VC7002
Accessory Open/Closed Sensor
for use with
ULE certified systems*
P
Add and register a sensor
Your new Open/Closed Sensor VC7002
can be registered to any ULE compatible
product.
Register each sensor individually to the
respective ULE compatible product before
use.
Register a sensor:
Enter the registration mode by selecting
the option for adding a sensor to your
ULE compatible product. Refer to the
user’s manual of your ULE compatible
product for more detailed instructions.
Press and hold the button on the P
Open/Closed Sensor, until the LED light
flashes red, to enter the registration
mode.
When the registration process is
complete, the red LED light on the sensor
will remain steady for about two seconds,
and then turn off. The registration
process takes about 90 seconds to
complete.
NOTE
You can also download online User’s manuals at
www.vtechcanada.com.
Replacing a sensor
If you have purchased this new VC7002
accessory sensor to replace an old sensor,
you must deregister the registered sensor
first, and then register this new sensor to
your ULE compatible product.
Deregister a sensor or all sensors:
Refer to the User’s manual of your ULE
compatible products to deregister a sensor
or all sensors.
1.
2.
3.
•
•
Check the sensor before use
1. Separate the sensor unit from the magnet
unit.
You will receive alerts at your ULE
compatible product. Refer to the
Installation guide or User’s manual of
your ULE compatible product for the
sensor alerts.
2. Combine the sensor unit with the magnet
unit.
•
Test the sensor signal strength
You can mount the Open/Closed Sensor on
a door, window, medicine cabinet, or any
object that opens or closes.
Before mounting the sensor, make sure you
test if the location you install the sensor is in
range from your ULE compatible product.
Use adhesive tape to hold the sensor
temporarily in place.
Mount the sensor to a higher position to
avoid obstacles or blockages. Depending
on surroundings and obstructing factors,
like walls or cabinets, the sensor may not
transmit to the baby unit properly.
1. Take the sensor unit and magnet unit to
the desired mounting location, and use
adhesive tape to hold them temporarily in
place at the object and the frame.
2. Enter the signal checking or testing mode
at your ULE compatible product to test the
sensor signal strength.
3. Open the door, window, or medicine cabinet
again and check whether a good signal is
received at your ULE compatible product.
NOTES
I
f No signal or Weak signal message is
displayed in sensor setup mode, mode, or if
you do not receive an alert when you open the
door, move the telephone base closer to the
mounting location or move the sensor closer to
the telephone base.
Depending on surroundings and obstructing
factors, like walls or cabinets, the sensor may
not transmit to the base properly.
After testing the sensor signal strength, mark
the mounting location on the door, window,
or medicine cabinet and its respective
frame. Then, remove the adhesive tape and
proceed to the mounting process.
•
•
•
•
Mount with tape
1. Attach mounting tape onto the C
rectangular area at the rear side of the
magnet unit,
2. Stick the magnet unit onto the door.
Mount with tape
You can choose one out of the four spacers
with suitable height, and then add it to the
magnet unit.
1. Push the spacer towards the magnet unit
until it securely clicks into place.
2. Attach mounting tape onto the C
rectangular area at the rear side of the
spacer.
3. Stick the magnet unit onto the door.
Go to www.vtechcanada.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Mount the sensor
We recommend you mount the magnet unit
on a door, window, or medicine cabinet,
and mount the sensor unit on its respective
frame.
You can use the spacers provided if there is
a difference in level between the door and
the frame. The spacer will help to align your
sensor to the correct height. You can also
use a spacer if the frame is too narrow or has
some decorative molding.
NOTES
You can mount the sensor unit with mounting
tape first, and then use screws later if you
decide to mount it at that location for long term.
Make sure the mounting surface is clean. A
textured surface or any imperfections to a
smooth surface can keep the mounting tape
from making a strong bond.
Align the magnet unit with sensor unit when
mounting.
The distance between the sensor unit and
magnet unit must be .less than 1 cm (0.4 inch)
•
•
•
•
c
Without spacer
Mount the magnet unit
With spacer (optional)
* Visit for the latest ULE compatible products.www.vtechphones.com/wireless-monitoring
> 1 cm
(0.4 inch)
> 1 cm
(0.4 inch)
> 1 cm
(0.4 inch)
< 1 cm
(0.4 inch)
What’s in the box
Your product package contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
Overview
Sensor overview
1 – Magnet unit
2 – Sensor unit
Sensor unit overview
1 – Latch button
Press to open the battery
compartment case.
2 – Back cover
3 – P (Pair) button
Press and hold to enter the registration
mode.
4 – LED light
Red for a second when the sensor is
powered on.
Flashes red when the sensor is in the
registration mode.
5 – Battery compartment case
•
•
•
•
P
P
Sensor unit Magnet unit
Spacer for
sensor unit
(optional)
Double-sided
mounting tape C
Spacers for magnet
unit
(optional)
Large screw x 2
(for fixing the
spacer on the
frame; optional)
Small screw x 2
(for fixing sensor
unit’s back cover on
the spacer; optional)
Double-sided
mounting
tape A
Double-sided
mounting
tape B
NOTE
The door images in this manual are for conceptual
reference only.
•
* The door frame is thicker than
the door.
User’s manual
(Canada version)
Mount with tape
1. Attach mounting tape onto the B
rectangular area at the rear side of the
back cover
2. Stick the sensor unit onto the frame.
Mount spacer with tape
1. Attach mounting tape onto the A
rectangular area at the rear side of the
spacer.
2. Stick the spacer onto the frame.
-OR-
Mount spacer with screws
1. Use a pencil to mark two holes on the
desired location on the frame, with the
aid of the two holes on the spacer of the
sensor unit. Then, remove the spacer and
drill two holes into the frame.
2. Align the holes on the spacer with the
holes on the frame. Tighten the large
screws into the holes to secure the spacer
onto the frame.
Mount sensor unit onto spacer
3. Press the latch button on the sensor unit to
open the battery compartment case from
the back cover.
4. Align the holes on the battery
compartment back cover with the holes on
the mounted spacer.
5. Tighten the small screws into the holes to
secure the back cover of the sensor onto
the mounted spacer.
6. Push the battery compartment case back
onto the back cover on the mounted
spacer until it securely clicks into place.
General product care
Taking care of your sensor
Your sensor contains sophisticated electronic
parts, so it must be treated with care.
Avoid rough treatment
Place the sensor down gently. Save the original
packing materials to protect your sensor if you
ever need to ship it.
Avoid water
Your sensor can be damaged if it gets wet. Do
not use the sensor outdoors in the rain, or handle
it with wet hands. Do not install the sensor near a
sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your sensor
Your sensor has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the sensor for
some time, remove the battery from the sensor.
Store the sensor in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the sensor. If you cannot find the answer
to your question, visit our website at
www.vtechcanada.com or call 1-800-267-7377 for
customer service.
The sensor
does not
work at all.
Make sure two AAA alkaline
batteries are installed.
The sensor may be deregistered
from the telephone base. Register
it back to your ULE compatible
product.
The sensor may be out of range.
Move the sensor closer to your
ULE compatible product.
Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and injury, including
the following:
Adult setup is required.
Do not use this product near water. For
example, do not use it next to a bath tub, wash
bowl, kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator
or heat register.
Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the product other than specified
access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling
can cause electric shock when the product is
subsequently used.
Periodically examine all components for
damage.
Children should be supervised to ensure that
they do not play with the product.
The product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion if
a wrong type of battery is used for the sensor unit.
Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
Do not open or mutilate the battery. Released
1.
2.
3.
4.
5.
6.
7.
8.
9.
•
•
•
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
Exercise care in handling batteries in order not to
create a short circuit with conductive materials.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless devices):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless devices and implanted cardiac
pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians
that:
Pacemaker patients
Should keep wireless devices at least six inches
from the pacemaker.
Should NOT place wireless devices directly over
the pacemaker, such as in a breast pocket, when
it is turned ON.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devices.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device
under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
•
•
•
•
•
•
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with
the FCC criteria. The sensor unit shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately 8 in
(20 cm) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This product meets the applicable Industry Canada
technical specifications.
RF radiation exposure statement
The sensor complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The sensor unit should be installed
and operated with a minimum distance of 8 in (20
cm) between the sensor and all persons’ body. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment complies also with Industry Canada
RSS-102 with respect to Canada’s Health Code 6
for Exposure of Humans to RF Fields.
•
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants
to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and
all accessories provided in the sales package
(“Product”) are free from defects in material and
workmanship, pursuant to the following terms
and conditions, when installed and used normally
and in accordance with the Product operating
instructions. This limited warranty extends only to
the Consumer for Products purchased and used in
the United States of America and Canada.
What will VTech do if the Product is not free
from defects in materials and workmanship
during the limited warranty period (“Materially
Defective Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair
or replace at VTech’s option, without charge,
a Materially Defective Product. If we repair
the Product, we may use new or refurbished
replacement parts. If we choose to replace
the Product, we may replace it with a new or
refurbished Product of the same or similar
design. We will retain defective parts, modules, or
equipment. Repair or replacement of the Product,
at VTech’s option, is your exclusive remedy. VTech
will return the repaired or replacement Products to
you in working condition. You should expect the
repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective
Product under the terms of this limited warranty,
this limited warranty also applies to the repaired
or replacement Product for a period of either (a)
90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining
on the original one-year warranty; whichever is
longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or
other liquid intrusion; or
Product that has been damaged due to repair,
alteration or modification by anyone other than
an authorized service representative of VTech;
or
Product to the extent that the problem
experienced is caused by signal conditions,
1.
2.
3.
network reliability, or cable or antenna systems;
or
Product to the extent that the problem is caused
by use with non-VTech accessories; or
Product whose warranty/quality stickers,
product serial number plates or electronic
serial numbers have been removed, altered or
rendered illegible; or
Product purchased, used, serviced, or shipped
for repair from outside the United States of
America or Canada, or used for commercial or
institutional purposes (including but not limited
to Products used for rental purposes); or
Product returned without a valid proof of
purchase (see item 2 on the next column); or
Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
To obtain warranty service, please visit our website
at www.vtechcanada.com or call 1-800-267-7377.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls
and features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the
Product failure is not covered by this limited warranty,
or proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and will
request that you authorize the cost of repair prior
to any further repair activity. You must pay for the
cost of repair and return shipping costs for the repair
of Products that are not covered by this limited
warranty.
What must you return with the Product to get
warranty service?
Return the entire original package and
contents including the Product to the VTech
service location along with a description of the
malfunction or difficulty; and
Include a “valid proof of purchase” (sales
receipt) identifying the Product purchased
(Product model) and the date of purchase or
receipt; and
Provide your name, complete and correct
mailing address, and telephone number.
4.
5.
6.
7.
8.
1.
2.
3.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to
this Product. VTech provides no other warranties for
this Product. The warranty exclusively describes all
of VTech’s responsibilities regarding the Product.
There are no other express warranties. No one
is authorized to make modifications to this limited
warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives
you specific legal rights, and you may also have
other rights, which vary from state to state or
province to province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for
ordinary use) are limited to one year from the date
of purchase. Some states/provinces do not allow
limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue,
inability to use the Product or other associated
equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this
Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales
receipt as proof of purchase.
Technical specifications
Frequency control Crystal controlled PLL
synthesizer
Transmit frequency 1921.536-1928.448 MHz
Channels 5
Sensor operating
temperature
0°F (-18°C) to 130°F (55°C)
Nominal effective
range
Maximum power allowed
by FCC and IC. Actual
operating range may vary
according to environment
conditions at the time of use.
Power requirements 2 x AAA alkaline batteries
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
This product is covered by U.S. Patent #8,825,043.
Other patents may be pending.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
Copyright © 2016 for VTech Technologies Canada Ltd.
All rights reserved. 01/16. VC7002_CA_CIB_V1.0
Designed to fit your home.
And your life.
Mount the sensor unit
Without spacer
With spacer (optional)
B
A
* The door is
thicker than
the door frame.
Tuotetiedot
| Merkki: | VTech |
| Kategoria: | Valvontakamera |
| Malli: | VC7002 |
Tarvitsetko apua?
Jos tarvitset apua merkille VTech VC7002 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Valvontakamera VTech Käyttöohjeet
14 Joulukuuta 2024
14 Joulukuuta 2024
Valvontakamera Käyttöohjeet
- Valvontakamera ORNO
- Valvontakamera Bosch
- Valvontakamera D-Link
- Valvontakamera Philips
- Valvontakamera TP Link
- Valvontakamera Kogan
- Valvontakamera Axis
- Valvontakamera Lorex
- Valvontakamera EMOS
- Valvontakamera Planet
- Valvontakamera Hikvision
- Valvontakamera V-Tac
- Valvontakamera CRUX
- Valvontakamera I-PRO
- Valvontakamera DVDO
- Valvontakamera Uniden
- Valvontakamera BIRDFY
- Valvontakamera MEE Audio
- Valvontakamera IOIO
- Valvontakamera Imou
- Valvontakamera BirdDog
- Valvontakamera Mobotix
- Valvontakamera Milesight
- Valvontakamera KJB Security Products
- Valvontakamera Vimar
- Valvontakamera Setti+
- Valvontakamera AVer
- Valvontakamera Foscam
- Valvontakamera Overmax
- Valvontakamera Alfatron
- Valvontakamera Burg-Wachter
- Valvontakamera ClearOne
- Valvontakamera AViPAS
- Valvontakamera Enabot
- Valvontakamera IDIS
Viimeisimmät Valvontakamera Käyttöohjeet
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024