Wasp WWS800 Käyttöohje
Wasp
Viivakoodin lukija
WWS800
Lue alta 📖 käyttöohje suomeksi merkille Wasp WWS800 (18 sivua) kategoriassa Viivakoodin lukija. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/18
Wasp Technologies WWS800 Cordless Scanner
User’s Manual
Document Number: W800-A1
Release Date: February 18, 2004
2004, Wasp
®
Technologies
All rights reserved.
WARNING
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Table of Contents
1.
Introduction ........................................................................ 1
2.
Installation .......................................................................... 2
2.1
Power Up the WWS800 Base Station ................................ 2
2.2
Power Up the WWS800 Cordless Scanner......................... 3
2.3
Setup RF Connection.......................................................... 3
2.4
Charging your WWS800 Cordless Scanner........................ 4
2.5
Interface Setting.................................................................. 5
3.
General Features................................................................. 6
3.1
Buzzer................................................................................. 6
3.2
Indicator ............................................................................. 6
3.3
Scan Modes ........................................................................ 6
3.4
Auto-Sense ......................................................................... 7
3.5
Re-read Delay..................................................................... 7
3.6
Scanner Time-out Duration ................................................ 7
3.7
Reading Redundancy .......................................................... 8
3.8
Supported Symbologies ...................................................... 8
3.9
Negative Barcodes.............................................................. 8
4.
Output Interface (WWS800 Base Unit).............................. 9
4.1
Keyboard Wedge Interface ................................................. 9
4.1.1
Keyboard Type ................................................................... 9
4.1.2
Keyboard Style - Alphabets................................................ 9
4.1.3
Keyboard Style – Digits ..................................................... 9
4.1.4
Capital Lock Status........................................................... 10
4.1.5
Alphabets Transmission.................................................... 10
4.1.6
Digits Transmission.......................................................... 10
4.1.7
Inter-Character Delay ....................................................... 10
4.2
USB Interface ................................................................... 10
4.3
Memory Parameters.......................................................... 11
4.3.1
Memory Mode .................................................................. 11
4.3.2
Clear Data......................................................................... 11
4.3.3
Send Data ......................................................................... 11
4.3.4
Memory Data Delay ......................................................... 11
5.
Bluetooth Serial Port ........................................................ 12
5.1
Configuring the WWS800 ................................................ 12
5.1.1
Activate Bluetooth Serial Port Interface........................... 12
5.1.2
Authentication & PIN Code.............................................. 12
5.1.3
Device Name Broadcasting .............................................. 12
5.1.4
Update Settings................................................................. 13
5.1.5
Timeout ............................................................................ 13
5.2
Configuring Bluetooth Device Driver .............................. 13
6.
Symbology Parameters ..................................................... 19
6.1
Code39 ............................................................................. 19
6.2
Italy / French Pharmacode ................................................ 19
6.3
Industrial / Interleave / Matrix 25..................................... 19
6.4
Codabar ............................................................................ 20
6.5
UPCE................................................................................ 20
6.6
EAN8................................................................................ 20
6.7
UPCA ............................................................................... 21
6.8
EAN13.............................................................................. 21
6.9
MSI................................................................................... 21
6.10
Plessey.............................................................................. 21
6.11
Telepen............................................................................. 22
6.12
RSS................................................................................... 22
7.
Data Output Format.......................................................... 23
7.1
Character Substitution ...................................................... 23
7.2
Prefix / Postfix Code ........................................................ 23
7.3
Code ID ............................................................................ 23
7.4
Length Code ..................................................................... 24
8.
Data Editing...................................................................... 25
8.1
Select Editing Format ....................................................... 25
8.2
Restore Default Format .................................................... 25
8.3
Applicable Conditions ...................................................... 25
8.4
Total Number of Fields .................................................... 26
8.5
Dividing Data into Fields ................................................. 26
8.6
Additional Fields .............................................................. 27
8.7
Field Transmission Sequence ........................................... 27
8.8
End of Format Programming ............................................ 27
8.9
Activate Data Editing Formats ......................................... 27
8.10
Exclusive Data Editing ..................................................... 27
8.11
Programming Examples.................................................... 27
9.
Configuring your WWS800.............................................. 29
9.1
Enter Configuration Mode................................................ 29
9.2
Default.............................................................................. 29
9.3
List Setting ....................................................................... 29
9.4
Setting Parameter Values.................................................. 29
9.4.1
Numeric Parameters ......................................................... 30
9.4.2
Character String Parameters ............................................. 30
9.4.3
Key Type/Status Setting ................................................... 31
9.5
Exit Configuration Mode.................................................. 32
The WWS800 Cordless Barcode Scanner is the first Wasp Technologies scanner
utilizing Bluetooth Technology. The scanner has a remote range of over 160 feet
and a battery life of over 50,000 scans. The WWS800 uses a CCD long-range
linear imager. This manual contains all the information needed to operate and
configure the WWS800. It is divided into two parts. The first part of this manual
describes the installation, operation and programmable features of the scanner. The
second part of this manual contains the setup barcodes used to configure the
scanner.
The WWS800 is one of the most versatile and flexible cordless barcode scanners
available today. All the features and functions required for up to date barcode
reading are included. Owing to the compact design and extremely low power
consumption, this scanner provides for easy installation and high product durability.
The scanner caters to the requirements of today, while also fulfilling your long-term
needs. The main functions and features provided on the WWS800 are listed below.
• Barcode Readability: Most popular barcode symbologies are supported including
the newest RSS Code.
• Support for negative barcodes.
• Supports eight scan modes.
• Programmable Beeping Tone
• Dual Color Indicator
• Interface Support (base unit): KB Wedge and USB
• Bluetooth Serial Port Profile Support: The scanner can transmit scanned data to
Bluetooth enabled computer/PDA via standard Bluetooth Serial Port
communication.
• Programmable Code ID: Code ID can be individually configured for each
symbology.
• Programmable Length Code
• Programmable Prefix Code
• Programmable Postfix Code
• Character Substitution
• Data Editing: Data can be reorganized according to user programmable formats.
Up to three data editing formats are supported.
• Extremely Low Power Consumption
The WWS800 kit contains:
WWS800 Cordless Barcode Scanner
WWS800 Base/Charger dock
Keyboard wedge or USB cable (depending on configuration ordered)
Power Supply for Base/Charger dock
CD containing this manual
Note : For installation and configuration instructions on
Bluetooth Serial Port operation, please refer to the section
“Bluetooth Serial Port”.
Keyboard Wedge connection USB connection
Connect the interface cable into the 15-pin connector at the back of the base. The
cable you connect will depend on the interface you ordered. The configurations
shown are the Keyboard Wedge and the USB cable connections.
IMPORTANT: First turn OFF your PC or Laptop that you are connecting the base
cable to. Connect the cable to the base and then plug the other end of the cable into
the appropriate connection on your PC as shown in the figures above.
Connect 5VDC jack of the power supply cable into the DC 5V port located at the
back of the base. Connect the AC plug to an AC outlet and then turn ON your PC.
You are now ready to configure your scanner and base.
Tuotetiedot
| Merkki: | Wasp |
| Kategoria: | Viivakoodin lukija |
| Malli: | WWS800 |
Tarvitsetko apua?
Jos tarvitset apua merkille Wasp WWS800 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Viivakoodin lukija Wasp Käyttöohjeet
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
Viivakoodin lukija Käyttöohjeet
Viimeisimmät Viivakoodin lukija Käyttöohjeet
26 Lokakuuta 2024
19 Lokakuuta 2024