Getac CA-NF42 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Getac CA-NF42 (4 sivua) kategoriassa Kamera. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/4
GETAC VIDEO SOLUTION
CA-NF42 Dual Lens IP Camera
QUICK START GUIDE
1. Unpacking
IP Camera
CA-NF42
Accessories
Windshield Mounting Kit
Mounting arm and
hex socket cap screw
Mounting plate, pad,
and screw x 2
2. Identifying Components
Front
No. Description
4K (8MP) camera lens and sensor
Status LED: It can be configured to
light up when the system is recording
with different intensities.
4K (8MP) camera lens and sensor
Rear
No. Description
Status LED Red: Boot up
Green: Ready
Microphone
Factory reset
Top
No. Description
PoE connector
5618xxxx0001 R00
3. Cautions and Notices
Notices
• The sale of this product is controlled by the National Defense
Authorization Act (NDAA), H.R. 5515.
• The camera must be professionally installed.
• Do not twist, squash, or bend the PoE cable (supplied separately).
• See Installation Diagram for more information.
Cautions
• Do not expose your skin to the camera when operating it in a very hot
or cold environment.
• The camera can get uncomfortably warm when you use it in high
temperatures. As a safety precaution in such a circumstance, do not
touch it with your bare hands for extended periods of time. Prolonged
contact can cause discomfort and potentially a burn.
• The camera may become very warm during normal use. It complies with
the user-accessible surface temperature limits defined by the International
Standards for Safety. Still, sustained contact with warm surfaces for long
periods of time may cause discomfort or injury.
• If the camera is used for long periods, its surface can become very warm.
While the temperature may not feel hot to the touch, if you maintain
physical contact with the camera for a long time, for example if you
touch it with your bare hands, your skin might suffer a low-heat injury.
FCC Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions
and do not make any unauthorized modifications.
FCC Note:
This equipment has been tested and found to comply with the limits for a
class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Warning:
To assure continued FCC emission limit compliance, the user must only use
shielded interface cables when connecting to external units. Also, any
unauthorized changes or modifications to this equipment could void the
user’s authority to operate this device.
Tuotetiedot
| Merkki: | Getac |
| Kategoria: | Kamera |
| Malli: | CA-NF42 |
Tarvitsetko apua?
Jos tarvitset apua merkille Getac CA-NF42 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kamera Getac Käyttöohjeet
17 Lokakuuta 2024
17 Lokakuuta 2024
17 Lokakuuta 2024
Kamera Käyttöohjeet
- Kamera Kogan
- Kamera Kodak
- Kamera Aplic
- Kamera UniView
- Kamera Minolta
- Kamera Elmo
- Kamera Linhof
- Kamera Imou
Viimeisimmät Kamera Käyttöohjeet
25 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024