Noise Engineering Cursus Iteritas Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Noise Engineering Cursus Iteritas (7 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/7
1
Type LFSR VCO
Size 10HP Eurorack
Depth 1.5 Inches
Power 2x8 Eurorack
+12 mA 150 / 80 (if 5v on)
-12 mA 5 / 5
+5 mA 0 / 90 (optional)
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
Cursus Iteritas is an oscillator that works from a dynamically generated
wavetable. It gives the user spectral-like controls over three different modes
based on different conceptualizations of frequency: Fourier, which uses sine
waves; Daubechies, using wavelets, and Walsh mode, using the Walsh
transform. Cursus Iteritas parametrizes a wide variety of sounds, but because
the sounds are all based off of orthogonal functions, it has a musical tone
structure and can produce an extremely wide variety of harmonic sounds.
Interface
All knobs on Cursus Iteritas function as offsets for the input jacks. The controls
function similar to a bandpass filter; center, width, and tilt allow the filter to be
asymmetric.
Pitch
1v/8va pitch control. For more control, see Range below.
Center
selects the center harmonic used to build the wavetable.
Structure
allows selection of harmonics included in the output. In the center
position, all harmonics are included. Fully left only even harmonics; fully right,
only odd.
Edge
controls the oversampling filter of the wavetable. As this is turned to the
right, it will add musical overtones.
Fold
wavefolder. Enough said.
Width
controls how many different harmonics are used to create the wavetable.
Tilt
weights the spread of harmonics. In the middle it is symmetric; at left,
lower harmonics are louder while at right, higher harmonics get more volume.
Sync
triggers edge-based oscillator reset
Mode
selects which orthogonal function set is used to produce the wavetable
Range
two-octave offset pitch ranges
Out
audio output - 10vpp
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
2
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
Patch Tutorial 0 - Introduction
The easiest way to get to know Cursus is to just plug in the output and play with the knobs to get a
feel for the sounds it can make.
Patch Tutorial 1
Cursus works very well with any LFO, gate or envelope source the more the better. Patching the
outputs of the Numeric repetitor directly into the parameter inputs on Cursus is a great way to generate
complex rhythmic tonality variation.
Every LFO source is fun with Cursus. We highly reccomend patching Sinc Iter, Malekko Voltage
Block, Malekko AD/LFO, Mannequins Just Friends, Make Noise Wogglebug, and WMD PDO with
Cursus.
Patch Tutorial 1 - Gates and LFO
We will be updating this with
pictures, more examples and
videos very soon!
3

Tuotetiedot

Merkki: Noise Engineering
Kategoria: Ei luokiteltu
Malli: Cursus Iteritas

Tarvitsetko apua?

Jos tarvitset apua merkille Noise Engineering Cursus Iteritas esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Noise Engineering Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet

Nec

Nec SDM-HDBT-R-UHD Käyttöohje

19 Maaliskuuta 2025
Nec

Nec SP-RM3 Käyttöohje

19 Maaliskuuta 2025
Milwaukee

Milwaukee PODS-1 Käyttöohje

19 Maaliskuuta 2025
Chord

Chord GB-50 Käyttöohje

19 Maaliskuuta 2025
Jan Nowak

Jan Nowak Eric Käyttöohje

19 Maaliskuuta 2025
Realme

Realme Buds Q2s Käyttöohje

19 Maaliskuuta 2025
Cubot

Cubot King Kong Tab Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast B9 Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast E14 Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast D16 Käyttöohje

19 Maaliskuuta 2025