Noise Engineering Pura Ruina Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Noise Engineering Pura Ruina (4 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/4
Overview
Pura Ruina is a three-stage CV-controlled fully-hyphenated full-wave rectifier/distortion designed for
audio. Simple waveforms can be manipulated into completely new and exciting tones, and already-
complex sounds can be shredded into sonic oblivion. Add some CV and you’ll never want to let PR out
of your rack! Each stage has an individual level control with corresponding CV and individual out, as
well as feeding to the universal Sum output. PR’s rectification creates a unique flavor of distortion
unlike standard wavefolding or clipping. The possibilities are virtually endless: add to a west-coast
style complex oscillator setup for unique timbral shaping, annihilate a percussion mix through it, run its
individual outs through other Ruina modules for further mayhem… You’ll never run out of awesome
things to try, we promise. You know you want one.
1
Noise Engineering
Pura Ruina
Three-stage CV-controlled full-wave rectifier.
Type
Three-stage rectifier/folder
Size
8HP Eurorack
Depth
.8 Inches
Power
2x5 Eurorack
+12 mA
75 mA
-12 mA
65 mA
Etymology
Ruina -- from Latin: “destruction”
Pura -- from Latin: “pure”
“Pure destruction”
CV inputs are all 0-5v.
Input & output voltages
Special Thanks
Shawn Jimmerson, as always, has been a guiding light throughout the development of this module.
Power
Screw your module into your case BEFORE powering on the
module. You risk bumping the module’s PCB against something
metallic and damaging it if it’s not properly secured when powered
on.
To power your Noise Engineering module, turn off your case. Plug
one end of your ribbon cable into your power board so that the red
stripe on the ribbon cable is aligned to the side that says -12v and
each pin on the power header is plugged into the connector on the
ribbon. Make sure no pins are overhanging the connector.
Line up the red stripe on the ribbon cable so that it matches the
white stripe and/or -12v indication on the board and plug in the
connector.
You should be good to go if you followed these instructions. Now
go make some noise!
A final note. Some modules have other headers -- they may have a
different number of pins or may say NOT POWER. In general,
unless a manual tells you otherwise, DO NOT CONNECT THOSE
TO POWER.
Warranty
This warranty does not cover damage due to improper handling, storage, use, or abuse, modifications, or
improper power or other voltage application.
Noise Engineering backs all our products with a product warranty: we guarantee our products to be free
from manufacturing defects (materials or workmanship) for one year from the date of the original retail
purchase (receipt or invoice required). The cost of shipping to Noise Engineering is paid by the user.
Modules requiring warranty repair will either be repaired or replaced at Noise Engineering's discretion. If
you believe you have a product that has a defect that is out of warranty, please contact us.
2
Interface
1:
Output for all four stages summed together.
Single full-wave rectification stage volume.
Dry signal volume.
All CV:
Double full-wave rectification volume.
8:
In:
Audio input.
See Design Notes (below) for information on full-wave rectification.
Outs 1/2/4/8:
Individual outputs for each section.
2:
Simultaneous control of all four CV inputs.
4:
CV control of volume for each stage. Knobs act as offsets for the CV inputs.
Sum Out:
Triple full-wave rectification volume.
CV ins 1/2/4/8:
3
8
CV Out
In
Sum
Out
All
CV
4
2
1
1
Pura Ruina
4
2
8
Patch Tutorial
PR can act as a complex VCA. Run an oscillator to the In jack and the Out jack to
your mixer. Run an envelope to the All CV input. PR now controls the volume of
your voice as well as adding harmonic complexity! For even more control, run
the envelope through a mult and attenuators (like Sinc Defero) and modulate each
section’s volume individually for more harmonic possibilities.
Second Patch:
Patch a simple waveform (like a sine wave) to the In jack. Patch the Sum Out
jack to your mixer. Adjust the knobs to see what kind of sounds PR can create.
Using the patch from the previous example, take a quad CV source like Mimetic
Digitalis and modulate the 1, 2, 4, and 8 CV inputs to create tonally evolving
sequences.
Fourth Patch:
First Patch:
Third Patch:
Patch a different type of sound (for instance, a percussive loop) and run it through
PR. New sounds are waiting to be discovered!

Tuotetiedot

Merkki: Noise Engineering
Kategoria: Ei luokiteltu
Malli: Pura Ruina

Tarvitsetko apua?

Jos tarvitset apua merkille Noise Engineering Pura Ruina esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Noise Engineering Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet

Nec

Nec SDM-HDBT-R-UHD Käyttöohje

19 Maaliskuuta 2025
Nec

Nec SP-RM3 Käyttöohje

19 Maaliskuuta 2025
Milwaukee

Milwaukee PODS-1 Käyttöohje

19 Maaliskuuta 2025
Chord

Chord GB-50 Käyttöohje

19 Maaliskuuta 2025
Jan Nowak

Jan Nowak Eric Käyttöohje

19 Maaliskuuta 2025
Realme

Realme Buds Q2s Käyttöohje

19 Maaliskuuta 2025
Cubot

Cubot King Kong Tab Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast B9 Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast E14 Käyttöohje

19 Maaliskuuta 2025
Acefast

Acefast D16 Käyttöohje

19 Maaliskuuta 2025