Sonance MAG06V3 Käyttöohje

Sonance Kaiutin MAG06V3

Lue alta 📖 käyttöohje suomeksi merkille Sonance MAG06V3 (4 sivua) kategoriassa Kaiutin. Tämä opas oli hyödyllinen 16 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/4

M AG06V3

OUTD O O R SPE A KE R

I N S T R U C T I O N M A N UA L

Scan QR Code

for product

installation video

INTRODUCTION

Thank you for purchasing Sonance MAGO6V3

weather-resistant speakers.

When properly installed, these speakers will give you

many years of outdoor entertainment pleasure. To get the

most out of your new speakers, please read this manual

thoroughly before you begin installation.

SONANCE OUTDOOR SPEAKER

MAGO6V3 INSTRUCTION MANUAL

BOX & CONTENTS

(2) Sonance MAGO6V3 speakers

(2) Speaker grilles

(2) Mounting brackets

(2) Wire terminal covers

(1) Set of mounting hardware

CONNECTING & ASSEMBLING

WARNING: TURN THE AMPLIFIER’S POWER OFF UNTIL YOU

HAVE COMPLETED ALL OF THE CONNECTIONS AND HAVE

DETERMINED THAT THEY ARE CORRECT. (IF THE AMP’S AC

PLUG IS ACCESSIBLE WE RECOMMEND THAT YOU UNPLUG

IT FROM THE WALL OUTLET TO AVOID ACCIDENTAL

TURN-ON AND POSSIBLE DAMAGE TO THE AMPLIFIER.)

SPEAKER PLACEMENT

Sonance MAGO6V3 Speakers are highly weather-resistant,

and when mounted outdoors will perform exceptionally well

for years even under adverse weather conditions.

The Sonance FastMount® bracket system makes it easy to

mount the speakers in a variety of positions and locations:

(see ﬁgure 1).

The best performance is obtained by placing the speakers at

ear level, facing the listeners.

• If you are mounting the speakers above or below ear level,

pivot them up or down to direct the sound towards the listeners.

Under an eave

Against a wall

(ﬂush)

In a corner

Pole mount

(hardware sold separately)

FIGURE 1:

SPEAKER PLACEMENT

FIGURE 2:

PASS WIRE

THROUGH HOLE

1. In most cases you will be able to attach the

FastMount brackets directly to the mounting

surface. Run the speaker wires from the

ampliﬁer to the speaker locations and through

the holes in the brackets (see ﬁgure 2).

2. Attach the FastMount brackets to the

mounting surface using the included

hardware that is appropriate for the type

of surface (see ﬁgure 3).

If the installation requires that the speaker

be mounted in a corner, attach the bracket

with hardware through the slots in the

angled corners (see ﬁgure 4).

3. If the installation requires that the speaker

be mounted on a pole you can attach the

FastMount brackets to the pole using 2.5”

U-bolts (not included) (see ﬁgure 5).

4. Feed the speaker wires from the bracket

into the wire entry grommet on the back

of the speaker, through the wire tunnel

and out the opening on the speaker’s

front panel (see ﬁgure 6).

5. Slide the speaker onto the bracket until

the locks snap into place. Pull enough

wire through the front of the speaker to

allow connection to the terminals

(see ﬁgure 7).

NOTE: TO INCREASE WATER RESISTANCE AND

MAKE INSTALLATION EASIER, THE SPEAKER

WIRE TERMINALS ARE LOCATED ON THE

MAGO6 SPEAKERS’ FRONT PANEL. BE SURE

TO LEAVE ENOUGH WIRE AT THE SPEAKER

LOCATION TO FEED THROUGH THE TUNNEL

IN THE SPEAKER ENCLOSURE AND CONNECT

TO THE TERMINALS ON THE FRONT.

FIGURE 3:

ATTACH BRACKET

FIGURE 4:

CORNER MOUNTING

• The grommet forms a water-resistant

seal around the speaker wire.

• Make sure there is enough slack in

the wire to allow the speaker to

pivot on the bracket.

FIGURE 5:

ATTACHING THE

BRACKET TO A POLE

FIGURE 6:

WIRE ENTRY

GROMMET

FIGURE 7:

ATTACH SPEAKERS

TO BRACKETS

7. Fit the wiring connector cover into the recess in the

speaker’s front panel. The cover should ﬁt tightly but can

be removed and replaced if the speaker needs to be

disconnected (see ﬁgure 9).

8. Fit the grille onto the speaker (see ﬁgure 10).

FIGURE 9:

ATTACH THE

CONNECTOR COVER

FIGURE 10:

ATTACH THE GRILLE

UNLOCK (toward rear of speaker)

LOCK (toward front of speaker)

FIGURE 11:

LOCK AND

UNLOCK

SLIDE LOCKS

TO PIVOT

SPEAKER

PIVOTING THE SPEAKER

You can rotate the speaker in the bracket to direct the sound

toward the listeners.

1. Unlock the slide locks on the speaker pivots by moving

them toward the rear of the speaker (see ﬁgure 11).

2. Rotate the speakers to the desired position.

3. Lock the slide locks by moving them toward the front of

the speaker.

IMPORTANT: BE SURE NOT TO LET ANY STRAY ‘+’ AND ‘–’

WIRES TOUCH EACH OTHER. TOUCHING WIRES CAN CAUSE

A SHORT- CIRCUIT THAT COULD DAMAGE YOUR AMPLIFIER.

• The spring connectors can accept wire up to 14 gauge.

• Double-check that you connected all of the wires

properly (ampliﬁer ‘+’ to speaker ‘+’; ampliﬁer ‘–’

to speaker ‘–’) at all connections.

SPECIFICATIONS

MAGO6V3 Speakers

Tweeter: 1” (25mm) cloth dome, Ferroﬂuid cooled,

in acoustic back chamber

Woofer: 6.5” (165mm) glass ﬁber cone

with a Santoprene surround

Frequency Response: 65Hz - 30kHz 3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 80 watts maximum

Sensitivity: 89dB SPL (2.83V/1 meter)

Environmental: Conforms to Mil Spec 810 for humidity, salt spray,

temperature and UV, IP-66 waterproof rating

Environment Temp: -13º - 149ºF (-25ºC - 65ºC)

Dimensions (WxHxD): 7.51” x 12.14” x 6.86” (191mm x 308mm x 174mm)

Grille: Perforated aluminum

Shipping Weight: 14 lbs. (6.4kg) pair

6. Connect the speaker wires to the

speaker’s terminals:

A. Strip about .5” of insulation from

each conductor and twist the strands

together or tin them with solder.

B. Press-down on the tops of the

connectors to open them.

C. Insert the wires into the connector

holes (see ﬁgure 8).

D. Release the connectors.

FIGURE 8:

CONNECTION TERMINALS

Tuotetiedot

Merkki:	Sonance
Kategoria:	Kaiutin
Malli:	MAG06V3

Tarvitsetko apua?

Jos tarvitset apua merkille Sonance MAG06V3 esitä kysymys alla ja muut käyttäjät vastaavat sinulle

Nimesi*

Sähköpostisi*

Kirjoita kysymyksesi tähän

Kaiutin Sonance Käyttöohjeet

Sonance Visual Experience VX86 Käyttöohje

27 Helmikuuta 2025

Sonance Invisible Series IS10 Käyttöohje

27 Helmikuuta 2025

Sonance Visual Experience VX86R SST Käyttöohje

27 Helmikuuta 2025

Sonance Visual Experience VX66R Käyttöohje

27 Helmikuuta 2025

Sonance Visual Performance Extreme VPXT8R Käyttöohje

8 Tammikuuta 2025

Sonance Visual Performance VP38R Käyttöohje

8 Tammikuuta 2025

Sonance MAG5.1R Käyttöohje

8 Tammikuuta 2025

Sonance MAG6R Käyttöohje

8 Tammikuuta 2025

Sonance Mariner MX52 Käyttöohje

31 Joulukuuta 2025

Sonance MAG06V3 Käyttöohje

26 Lokakuuta 2024

Kaiutin Käyttöohjeet

Viimeisimmät Kaiutin Käyttöohjeet

LD Systems STINGER G3 TMB Käyttöohje

8 Huhtikuuta 2025

JBL Conceal C83 Käyttöohje

8 Huhtikuuta 2025

JBL Control 426LP Käyttöohje

8 Huhtikuuta 2025

Crestron SAROS ICE4T Käyttöohje

7 Huhtikuuta 2025

Crestron SAROS ICI6T Käyttöohje

7 Huhtikuuta 2025

Crestron SAROS IC8T Käyttöohje

7 Huhtikuuta 2025

Focal K2 Power M FRAK Käyttöohje

5 Huhtikuuta 2025

Turbosound PQ12-SB Käyttöohje

3 Huhtikuuta 2025

Trust Tytan GXT 658 Käyttöohje

3 Huhtikuuta 2025

Turbosound PQ15-YB Käyttöohje

3 Huhtikuuta 2025